2 | SmithsEP.co.uk | Issue 001 - July 2022
Issue 001 - July 2022 | SmithsEP.co.uk | 3
Declaration of conformity
EC Declaration of conformity
We, Smith’s Environmental Products Limited
1-2 Blackall Industrial Estate
South Woodham Ferrers
Chelmsford
Essex CM3 5UW
Tel: 01245 324900 Fax: 01245 324422
Declare under sole responsibility that the products:
Product name:
Ecovector ll Smart LL
Product range:
LL640, LL1030, LL1390
Conform to the following European
Union directives:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Pressure Equipment directive 97/23/EC
Safety Directive 98/37/EC
Standards Comply With The Above Directives.
Safety Directive Standards:
EN 60335-2-80:2003 + A1:04 in conjunction
with EN 60335-1:2002 + A11:04 + A1:04 +
A12:06 + A2:06 With U.K deviations.
EMC Directive Standards:
EN 55014-1:2000+A1:01+A2:02
EN 61000-3-2:2000
EN 61000-3-3:1995+A1:01+A2:05
EMF Standards:
EN 50366:2003+A1:06
This Declaration is made on behalf of Smith’s
Environmental Products Limited.
Salus controller
The Salus controller independently complies with
the essential requirements and other relevant
provisions of Directives 2014/30/EU, 2014/35/EU,
2014/53/ EU and 2011/65/EU. The full text of the
EU Declaration of Conformity is available at the
following internet address: www.saluslegal.com.
Introduction
In the event of items missing or visible damage
please contact us on 01245 324560.
This heating appliance is intended for
mounting on a wall at low level. The minimum
recommended installation height is 100mm from
the floor. There is no clearance required on either
side of the heater.
This heater must not be used in bathrooms or
other high humidity areas.
Ecovector ll Smart LL is designed for use on
standard two-pipe pumped central heating
systems where the system hot water is generated
from either a boiler or renewable sources. This
product is not suitable for one-pipe heating
systems. Pipe connections are 15mm.
We recommend the use of full flow isolating
valves. These valves should be accessible after
completion of the installation.
Ecovector ll Smart LL is classified as a fixed
appliance and electrical connection should be via
a double pole 3A fused spur. The fused spur must
not be directly above the heater but should be
accessible after completion of the installation. If
the pre-wired mains cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified persons. The appliance must be
earthed.
To avoid possibility of vibration, this product must
be installed on a flat, even surface.
To comply with Building Regulations Part L (Part J
in Scotland) this heater is fitted and controlled by
an integral room thermostat
Please note the guarantee may be invalidated
if this product is not installed and used in
accordance with this guide.
Contents
Introduction 2
Declaration of conformity
3
Symbols used in this guide
3
Important safety and installation instructions
4
Product dimensions
6
Wiring diagrams
6
Product performance
7
Installation 8
Commissioning 9
Heating Operation
9
User guide for Wi-Fi thermostat
10
Getting started - programming
your thermostat
12
Fault finding
16
User Manual
17
How it works
18
How to operate
18
Adding controls to network (UG600)
20
Fault finding
22
Accessories 23
Registering your product
23
Disposal 23
After sales and spares
23
Symbols
This manual contains information and
prescriptions marked by the following symbols.
Ignoring these safety provisions
marked by the symbol “caution:
hazard” may endanger the safety
of people.
Ignoring these safety provisions
marked by the symbol “caution:
electricity” may endanger the
safety of people, as well as the
integrity of things.
The removal of the screws can
cause the output of hot fluids
under high pressure from heating
system. Drain the system or close
the isolating valves.
High temperature surface. Take
utmost care to prevent people
from getting in contact with the
hot surfaces of the appliance.
