manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-124 Automatic Transmission: 

Oil Pump Assembly Disassembly and 
Reassembly

S4RS0A5106028

Disassembly

1) Remove O-ring from pump body.
2) Remove 8 oil pump subassembly bolts (1) and stator 

shaft assembly (2).

3) Remove oil seal (1) using special tool.

Special tool
(A):  09913–50121

Reassembly

1) Install new oil pump body oil seal (1).

Use special tool and hammer to install it, and then 
apply grease to its lip portion.

Special tool
(A):  09913–85210

“A”:  Grease 99000–25030

2) Install driven gear and drive gear to oil pump body 

after applying A/T fluid.

3) Install stator shaft assembly to oil pump body and 

tighten 8 pump subassembly bolts (1) to 
specification.

Tightening torque
Oil pump subassembly bolt (a):  10 N·m (1.0 kg-
m, 7.5 lb-ft)

4) After applying A/T fluid to new O-ring, install it to oil 

pump body.

5) Check drive gear for smooth rotation by using torque 

converter (1).

Oil Pump Assembly Inspection

S4RS0A5106029

1) Check body clearance of driven gear (1).

Push driven gear to one side of oil pump body (2). 
Using a feeler gauge, measure clearance between 
driven gear and body. If clearance exceeds its 
standard value, replace oil pump assembly.

Clearance between oil pump driven gear and oil 
pump body
Standard: 0.10 – 0.17 mm (0.0039 – 0.0067 in.)

2. Oil pump body

2. Oil pump body

2

1

I4RS0A510041-

I2RH0B510150-

I2RH0B510151-

1, (a)

I4RS0A510042-

1

I4RS0A510043-

I2RH0B510154-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Бренд: SAF-HOLLAND Страницы: 20
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Бренд: TEINHOF Страницы: 2
Lincoln NAUTILUS 2022 Owner'S Manual preview
NAUTILUS 2022
Бренд: Lincoln Страницы: 586
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Бренд: Audiovox Страницы: 8
Ford Fusion 2019 Supplement Manual preview
Fusion 2019
Бренд: Ford Страницы: 51
SIXTOL DRY CAR Instructions For Use Manual preview
DRY CAR
Бренд: SIXTOL Страницы: 32
Skoda 2015 Superb Owner'S Manual preview
2015 Superb
Бренд: Skoda Страницы: 276
Gentex Full Display Mirror Installation Instructions Manual preview
Full Display Mirror
Бренд: Gentex Страницы: 18
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Бренд: Mercedes-Benz Страницы: 66
Kia Soul 2018 Owner'S Manual preview
Soul 2018
Бренд: Kia Страницы: 673
Brodit 841488 Quick Start Manual preview
841488
Бренд: Brodit Страницы: 2
Dodge 2008 Dakota Owner'S Manual preview
2008 Dakota
Бренд: Dodge Страницы: 439
BrandMotion AVMS-3604 Installation Instructions Manual preview
AVMS-3604
Бренд: BrandMotion Страницы: 9
Kia D9062 ADU00 Manual preview
D9062 ADU00
Бренд: Kia Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды