manualshive.com logo in svg

Suzuki FL2, Руководство по установке

Поделиться
Скачать
Suzuki FL2 Скачать руководство пользователя страница 22

21

HEADLIGHT BEAM ADJUSTMENT 
(RIGHT AND LEFT)

The headlight beam can be adjusted up and down if
necessary.

To adjust the beam up and down:

Turn the adjuster screw clockwise or counterclockwise.

A: Adjuster screw

FRONT DIFFERENTIAL GEAR OIL (FOR LT-A400F)

Place the vehicle on a level ground.
Check the front differential gear oil levels as follows.
Remove the oil level bolt.
If the oil level is below the level hole, add the gear oil
through the filler hole until the oil flows out from the
level hole.
Reinstall the oil level bolt and the oil filler plug.
Tighten them securely.

A: Oil filler plug
B: Oil level bolt

FINAL GEAR OIL

Place the vehicle on a level ground.
Check the final gear oil levels as follows.
Remove the oil level bolt.
If the oil level is below the level hole, add the gear oil
through the filler hole until the oil flows out from the
level hole.
Reinstall the oil level bolt and the oil filler plug.
Tighten them securely.

A: Oil filler plug
B: Oil level bolt

NOTE:
• Use hypoid gear oil SAE 90, API grade GL-5.
• If the vehicle is ridden where the ambient temper-

ature is below 0°C or 32°F, use the hypoid gear
oil SAE 80, API grade GL-5.

NOTE:
• Use hypoid gear oil SAE 90, API grade GL-5.
• If the vehicle is ridden where the ambient temper-

ature is below 0°C or 32°F, use the hypoid gear
oil SAE 80, API grade GL-5.

Содержание FL2


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды