manualshive.com logo in svg

Suzuki FL2, Руководство по установке

Поделиться
Скачать
Suzuki FL2 Скачать руководство пользователя страница 19

18

THROTTLE CABLE

Check the throttle cable play at the throttle lever end.

Throttle cable play: 3.0–5.0 mm

If adjustment is necessary, carry out the following pro-
cedure.

1. Shift the rubber boot 

C

.

2. Loosen the throttle cable adjuster lock nut 

B

.

3. Turn the adjuster 

A

 to obtain the correct play.

4. Tighten the lock nut 

B

 while holding the adjuster 

A

.

5. Place the rubber boot 

C

.

CHOKE CABLE

Check the choke cable play.

Choke cable play: 0.5-1.0 mm

If adjustment is necessary, carry out the following pro-
cedure.

1. Shift the rubber boot 

C

.

2. Loosen the lock nut 

B

 and turn the adjuster 

A

 to

obtain the correct play.

3. Move the cable back and forth firmly to ensure that

the correct amount of free play is available and that
the cable housing is properly seated in the adjuster

A

.

4. Tighten the lock nut 

B

 while holding the adjuster 

A

.

5. Place the rubber boot 

C

.

REAR/PARKING BRAKE

Adjust the rear brake by adjusting the brake pedal first
and then adjust the brake lever.

WARNING

Inadequate throttle cable play can cause engine
speed to rise suddenly when you turn the han-
dlebars. This can lead to loss of rider control.

Adjust the throttle cable play so that engine idle
speed does not rise due to handlebar move-
ment.

WARNING

The rear brake lever and brake pedal operate
the rear brake in a complementary manner.
When one of these is misadjusted, the brake
system as a whole will not operate properly.
Misadjusting the rear brake lever and brake
pedal can cause brake dragging or inadequate
braking performance.

Adjust both the brake pedal and brake lever
within the specified range.

Содержание FL2


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды