background image

11

FLAME CHECK

A periodic visual check of the flames should be made. The pilot flame should always be present when the appliance 
is in operation. 

The flames should be yellow in color and should not be impinging on any of the logs.

For your safety, the appliance is equipped with an ODS (Oxygen Depletion Sensor) system. The system senses the 
oxygen in the atmosphere and switches off the gas supply in case the level of oxygen falls below a safe level. 

SCVFMR FLAME CHARACTERISTICS

THINGS TO DO

1. Use only the type of gas for which your system is designed. The type of gas the system is equipped for is marked on 

the rating plate. 

2. Install appliance and all gas piping according to local codes. 
3. Disconnect or isolate the system during line pressure testing.
4. Make sure 1/2” gas line is run to the fireplace to ensure sufficient gas volume to the appliance.
5. Install the the system only in a fireplace suitable for burning solid fuel.
6. Use pipe dope on threaded joints of gas piping that is resistant to the action of LP gas.
7. Install a manual shut-off valve, union and 1/8” NPT plugged pressure tap ahead of controls.
8. Use soap and water solution when checking for leaks.
9. Keep the area around the appliance clear and free of combustible materials, gasoline and any flammable or explosive

material.

10. Follow the lighting and operating procedures given in this manual.
11. Periodically inspect the pilot and burner flame.
12. Clean the appliance as described in the manual.
13. Keep logs properly positioned. 

THINGS NOT TO DO

1. Do not modify or alter this appliance in any way. 
2. Do not use this appliance with any gas other than that for which it was equipped. 
3. Do not install this appliance in any area where gasoline or any flammable material is used or stored. 
4. Do not use open flame to check for leaks. 
5. Do not operate this system with glass doors in the closed position. 
6. Do not block or restrict any grills of a factory built fireplace in which this appliance is installed. 
7. Do not burn solid fuels in a fireplace where this appliance is installed. 

Содержание SCVFMR 21
















Отзывы: