Supero SUPERSERVER 5015A-EHF Скачать руководство пользователя страница 11

Страница: 11 / 106

Chapter 1

Introduction

1-1 Overview

The Supermicro SuperServer 5015A-EHF is a single processor, 1U rackmount

server. The 5015A-EHF is comprised of two main subsystems: the SC502L-200B

chassis and the X7SPE-HF motherboard. Please refer to our web site for information

on operating systems that have been certifi ed for use with the 5015A-EHF.

In addition to the mainboard and chassis, various hardware components may have

been included with the 5015A-EHF, as listed below.

•

One SATA cable (CBL-0061L)

•

One CD containing drivers and utilities

•

SuperServer 5015A-EHF User's Manual

Optional Parts:

•

One dual 2.5" fi xed HDD bracket (MCP-220-00044-0N)

•

One single 2.5" fi xed HDD bracket (MCP-220-00051-0N)

Note:

a complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm

Chapter 1: Introduction

1-1

Содержание SUPERSERVER 5015A-EHF











































































































Результаты поиска

Содержание SUPERSERVER 5015A-EHF

Отзывы:

Supero SUPERSERVER 5015A-EHF, Руководство пользователя, Страница: 11 / 106

Результаты поиска

Содержание SUPERSERVER 5015A-EHF

Отзывы: