Supero SUPER P6SWA Скачать руководство пользователя страница 56

Страница: 56 / 88

BIOS Manual

4-6

BIOS

AMIBIOS checks for a <Del> key press and runs AMIBIOS

Setup if the key has been pressed.

Enabled

AMIBIOS does not test system memory above 1 MB.

AMIBIOS does not wait up to 40 seconds for a READY signal

from the IDE hard disk drive. If a READY signal is not

received immediately from the IDE drive, AMIBIOS does not

configure that drive. AMIBIOS does not wait for .5 seconds

after sending a RESET signal to the IDE drive to allow the IDE

drive time to get ready again. In

Enabled,

keyboard will be

bypassed.

Note: You cannot run AMIBIOS Setup at system boot, because there is

no delay for the "Hit <Del> to run Setup" message

Pri Master ARMD Emulated as

Pri Slave ARMD Emulated as

Sec Master ARMD Emulated as

Sec Slave ARMD Emulated as

Options for Pri Master ARMD Emulated as, Pri Slave ARMD Emulated as,

Sec Master ARMD Emulated as and Sec Slave ARMD Emulated as are

Auto, Floppy

Hard disk

1st Boot Device

2nd Boot Device

3rd Boot Device

The options for the 1st Boot Device are

Disabled, 1st IDE-HDD, 2nd IDE-

HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy, ARMD-FDD, ARMD-HDD, ATAPI

CD ROM, SCSI, Network

. The options for the 2nd Boot Device are

Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy,

ARMD-FDD, ARMD-HDD, ATAPI CD ROM or SCSI

. The options for the 3rd

Boot Device are

Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th

IDE-HDD, Floppy, ARMD-FDD, ARMD-HDD or ATAPI CD ROM

1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD and 4th IDE-HDD are the four hard

disks that can be installed by the BIOS. 1st IDE-HDD is the first hard disk

installed by the BIOS, 2nd IDE-HDD is the second hard disk, and so on. For

example, if the system has a hard disk connected to Primary Slave and

another hard disk to Secondary Master, then 1st IDE-HDD will be referred to

as the hard disk connected to Primary Slave and 2nd IDE-HDD will be

referred to as the hard disk connected to the Secondary Master. 3rd IDE-

HDD and 4th IDE-HDD are not present. Note that the order of the initializa-

tion of the devices connected to the primary and secondary channels are

Primary Master first, Primary Slave second, Secondary Master third, and

Содержание SUPER P6SWA

























































































Результаты поиска

Содержание SUPER P6SWA

Отзывы:

Похожие инструкции для SUPER P6SWA

Бренды по названию

Популярные бренды

Supero SUPER P6SWA, Руководство пользователя и BIOS

Результаты поиска

Содержание SUPER P6SWA

Отзывы:

Похожие инструкции для SUPER P6SWA

Бренды по названию

Популярные бренды