Supero SUPER P3TDE6 Скачать руководство пользователя страница 13

Страница: 13 / 90

Chapter 1: Introduction

1-7

Introduction

P3TDE6 Quick Reference

Jumper

Description

Default Setting

JA2

LVD SCSI Ch A Term.

Open (Enabled)

JA4

LVD SCSI Ch B Term.

Open (Enabled)

JA6

50pin SCSI Ch B Term

Open (Enabled)

JBT1

CMOS Clear

Pins 1-2 (Normal)

JP1

FSB Speed Setting

Pins 1-2 (Auto)

JP3

Spread Spectrum

Open (Disabled)

JP55

Third P/S Fail Enable/Disable

Open (Disabled)

JP56

Speaker Enable/Disable

Closed (Enabled)

JP57

BIOS Select

Pins 1-2 (BIOS1)

JP58

LAN/NIC Enable/Disable

Open(Enabled)

JP60

SCSI Enable/Disable

Pins 1-2 (Enabled)

JP61

PCI 66/33 MHz Select

Open (66 MHz)

JP62

Thermal Fan Enable/Disable

Closed (Enabled)

JP64

Watchdog Enable/Disable

Open (Disabled)

JP65

CPU/CPU Chassis Fan Select

Closed (CPU Fan)

Connector

Description

ATX POWER #1

Primary ATX Power Connector

ATX POWER #2

Secondary ATX Power Connector

BANK0-BANK1

Memory (RAM) Slots

COM1/COM2

COM1/COM2 Serial Port Connector

CPU1/CPU2

CPU 1 and CPU2 Sockets

CPU/CH/OH FAN

CPU/Chassis/Overheat Fan Headers

J13, J14

IDE Hard Disk Drive Connectors

J15

Floppy Disk Drive Connector

J16

Parallel Printer Port

J18

PS/2 Keyboard/Mouse Ports

JA1

Ultra160 LVD SCSI CH A Connector

JA3

Ultra160 LVD SCSI CH B Connector

JF1

Front Control Panel Connector

JP52

Chassis Intrusion Header

JP54

Third Power Supply Fail Header

JP63

NMI (Non-Maskable Interrupt) Connector

LAN

Ethernet Port

PWR_SEC

Secondary ATX Power Connector

SLED1

SCSI Active LED Header

USB

Universal Serial Bus Ports

WOL Wake-on-LAN Header
WOR

Wake-on-Ring Header

Содержание SUPER P3TDE6



























































































Результаты поиска

Содержание SUPER P3TDE6

Отзывы:

Похожие инструкции для SUPER P3TDE6

Бренды по названию

Популярные бренды

Supero SUPER P3TDE6, Руководство пользователя

Результаты поиска

Содержание SUPER P3TDE6

Отзывы:

Похожие инструкции для SUPER P3TDE6

Бренды по названию

Популярные бренды