Supermicro X9DRD-iF Скачать руководство пользователя страница 37

Страница: 37 / 115

Chapter 2: Installation

2-11

BMC CTRL

LAN CTRL

BIOS

CTRL

COM1

1.10

Rev.

X9DRD-iF

JBT1

LED2

LEDM

LED3

JIPMB1

JUIDB

JPW4

SP1

JSTBY1

JRK1

JPW3

JPW2

JPW1

JBAT1

JOH1

JI2C2

JI2C1

JWD1

JPG1

JPB1

JPL1

FAN4

FAN8

FAN7

T-SGPIO2

T-SGPIO1

SCU0

I-S

JTPM

USB6

USB4/5

USB8/9

CPU1

SLOT7 PCI-E 3.0 X8

CPU2

CPU1

SLOT4 PCI-E 3.0 X8

SLOT3 PCI-E 3.0 X8

SLOT5 PCI-E 3.0 X8

SLOT6 PCI-E 3.0 X1

COM2

VGA

LAN2

LAN1

USB2/3

IPMI_LAN

USB0/1

JPME
1

LAN

CTRL

BMC

CLK CTRL

JVR1

JVR2

JVRM_I2C

PCH

JSD1

I-S

I-SA
TA

SCU1

SCU2

SCU3

S-SGPIO1

JPW5

JPI2C1

:OH LED

JPME
2

CPU1

CPU2

Release Tabs

Notches

2-4 Installing and Removing the Memory Modules

Note

: Check Supermicro's website for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM

modules to prevent any possible damage.

Installing & Removing DIMMs

1. Insert the desired number of DIMMs into the memory slots, starting with P1-

DIMMA1.

2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.

Removing Memory Modules

Press both notches on the ends of the DIMM module to unlock it. Once it is loos-
ened, once it is loosened, remove it from the memory slot.

3. Align the key of the DIMM module with the receptive point on the memory

slot.

4. Align the notches on both ends of the module against the receptive points on

the ends of the slot.

5. Use two thumbs together to press the notches on both ends of the module

straight down into the slot until the module snaps into place.

6. Press the release tabs to the locking positions to secure the DIMM module

into the slot.

Press both notches straight
down into the memory slot at
the same time.

Содержание X9DRD-iF




















































































































Результаты поиска

Содержание X9DRD-iF

Отзывы:

Похожие инструкции для X9DRD-iF

Бренды по названию

Популярные бренды

Supermicro X9DRD-iF, Руководство пользователя

Результаты поиска

Содержание X9DRD-iF

Отзывы:

Похожие инструкции для X9DRD-iF

Бренды по названию

Популярные бренды