Supermicro SuperServer E300-8D Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 107

Supermicro SuperServer E300-8D Скачать руководство пользователя страница 37

37

Chapter 3 Motherboard Connections

VGA Enable/Disable

Jumper JPG1 allows you to enable or disable the VGA port using the onboard graphics
controller. The default setting is Enabled.

VGA Enable/Disable

Jumper Settings

Jumper Setting

Definition

Pins 1-2

Enabled

Pins 2-3

Disabled

PCI-E Slot SMB Enable

I2C1/I2C2 are used to enable PCI-E SMB (System Management Bus) support to improve
system management for the onboard PCI-E slot.

SMB to PCI-E Slots (JI

2

C1/JI

2

C2)

Jumper Settings

Jumper Setting

Definition

Pins 1-2

Enabled

Pins 2-3

Disabled (Default)

Watch Dog

JWD1 controls the Watch Dog function. Watch Dog is a monitor that can reboot the system
when a software application hangs. Jumping pins 1-2 will cause Watch Dog to reset the
system if an application hangs. Jumping pins 2-3 will generate a non-maskable interrupt
signal for the application that hangs. Watch Dog must also be enabled in BIOS. The default
setting is Reset.

Note:

When Watch Dog is enabled, the user must write their own application

software to disable it.

Watch Dog

Jumper Settings

Jumper Setting

Definition

Pins 1-2

Reset

Pins 2-3

NMI

Open

Disabled

BMC Enabled

JPB1 allows you to enable the BMC (Baseboard Management Control) chip and the onboard
IPMI connection for debugging purpose only. After the BMC is disabled, IPMI health and
remote management functions are no longer supported.

Note:

Keep BMC enabled to make

sure that the platform operates reliably with the health monitor.

BMC Enabled

Jumper Settings

Pin# Definition

1-2

Enabled
(Default)

2-3

Disabled

«
...
35
36
37
38
39
...
»

Содержание SuperServer E300-8D












































































































Отзывы:

Нет отзывов