Supermicro SUPERSERVER 6015V-MR Скачать руководство пользователя страница 51

Страница: 51 / 114

Chapter 5: Advanced Serverboard Setup

5-15

Extra Universal Serial Bus
Headers

Two additional USB headers (JUSB1/

JUSB2) are located near the ﬂ oppy

connector. These may be connected

for front side USB access. A USB

cable (not included) is needed for the

connection. See the table on the right

for pin deﬁ nitions.

Front Panel Universal Serial Bus

Pin Deﬁ nitions (JUSB1/JUSB2)

USB2
Pin # Deﬁ nition

USB3
Pin # Deﬁ nition

+5V

PO-

PO+

Ground

Key

No connection

Alarm Reset Header

(JAR)

Pin Setting Deﬁ nition

Pin 1

Ground

Pin 2

+5V

Alarm Reset

The system will notify you in the event

of a power supply failure. This feature

assumes that Supermicro redundant

power supply units are installed in the

chassis. Connect a microswitch to

the JAR header to disable the power

supply fail alarm.

Note:

the 6015V-MR/6015V-MRLP

has only a single power supply so this

header is unused

SGPIO

The two headers labeled SGPIO1

and SGPIO2 are for SGPIO (Se-

rial General Purpose Input/Output).

SGPIO provides a bus between the

SATA controller and the SATA drive

backplane to provide SATA enclosure

management functions. Connect the

appropriate cables from the back-

plane to the SGPIO1 and SGPIO2

headers to utilize SAS management

functions on your system.

SGPIO Header

Pin Deﬁ nitions (SGPIO1, SGPIO2)

Pin# Deﬁ nition Pin # Deﬁ nition

Ground

Data

Load

Ground

Note:

NC indicates no connection.

Содержание SUPERSERVER 6015V-MR



















































































































Результаты поиска

Содержание SUPERSERVER 6015V-MR

Отзывы:

Похожие инструкции для SUPERSERVER 6015V-MR

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6015V-MR, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6015V-MR

Отзывы:

Похожие инструкции для SUPERSERVER 6015V-MR

Бренды по названию

Популярные бренды