Supermicro SUPERSERVER 6015V-MR Скачать руководство пользователя страница 14

Страница: 14 / 114

1-4

UPER

ERVER 6015V-MR/6015V-MRLP User's Manual

1-3 Server

Chassis

Features

The SuperServer 6015V-MR/6015V-MRLP is built on the SC512F-520/SC512F-280

1U rackmount server chassis. The following is a general outline of the main features

of the SC512F-520/SC512F-280 chassis.

System Power

When conﬁ gured as the SuperServer 6015V-MR/6015V-MRLP, the SC512F-520/

SC512F-280 chassis features a single power supply.

Serial ATA Subsystem

The SC512F-520 (6015V-MR) chassis is designed to support one internal Serial

ATA hard drive and the SC512F-280 (6015V-MRLP) chassis is designed to support

two internal Serial ATA hard drives. The internal Serial ATA drives are not hot-swap-

pable.

Control Panel

The SC512F-520/SC512F-280's control panel provides important system monitoring

and control information. LEDs indicate power on, network activity, hard disk drive

activity, overheat warning and fan failure. The control panel also includes a main

power button and a reset button.

Rear I/O Panel

The rear I/O panel on the SC512F-520/SC512F-280 provides one PCI expansion

card slot, one COM port (another is internal), two USB ports, PS/2 mouse and

keyboard ports, a VGA (graphics) port and two Gb Ethernet ports. (See Chapter

6 for diagram.)

Cooling System

The SC512F-520/SC512F-280 chassis has an innovative cooling design that fea-

tures an air shroud and 4-cm counter-rotating fans with user-deﬁ ned fan speed

control. The SC512F-520 (6015V-MR) has three and the SC512F-280 (6015V-

MRLP) has two of these counter-rotating fans. (Fan speed may be deﬁ ned with

a BIOS setting.)

Содержание SUPERSERVER 6015V-MR



















































































































Результаты поиска

Содержание SUPERSERVER 6015V-MR

Отзывы:

Похожие инструкции для SUPERSERVER 6015V-MR

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 6015V-MR, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 6015V-MR

Отзывы:

Похожие инструкции для SUPERSERVER 6015V-MR

Бренды по названию

Популярные бренды