Supermicro SuperServer 5019C-FL Скачать руководство пользователя страница 51

Страница: 51 / 120

Chapter 4: Motherboard Connections

4.5 LED Indicators

IPMI LAN LEDs

A dedicated IPMI LAN, supported by the onboard Baseboard Management controller, is
located on the I/O panel. The amber LED on the right blinks to indicate activity. The LED on
the left indicates the speed of the connection.

IPMI LAN Link LED (Left)

LED State

LED Color

Definition

Off

No Connection/10 Mbps

Amber

1 Gbps

Green

100 Mbps

BMC Heartbeat LED

A BMC Heartbeat LED is located at LED2 on the motherboard. When it is blinking, the BMC
is functioning normally.

Unit ID LED

A rear UID LED indicator (LED4) is located near the UID switch on the I/O panel. If activated,

this LED provides easy identification of a unit that may need service.

Onboard Power LED

The Onboard Power LED is located at LED3 on the motherboard. When this LED is on, the
system is powered on.

Catastrophic Error LED

A CATERR LED is located at LED5. The orange LED indicates the system has experienced
a catastrophic error.

LAN LEDs

Two Ethernet LAN ports (LAN 1, LAN 2) are located on the I/O panel (front or rear). Each

port has two LEDs. One LED indicates activity when flashing amber. The other LED may be

green, amber or off to indicate the speed of the connection.

LAN Link LED

LED State

LED Color

Definition

Off

No Connection/10 Mbps

Amber

1 Gbps

Green

100 Mbps

Activity LED

Link LED

LAN 1/LAN 2

IPMI LAN

(X8ST3-F)

Содержание SuperServer 5019C-FL

























































































































Результаты поиска

Содержание SuperServer 5019C-FL

Отзывы:

Похожие инструкции для SuperServer 5019C-FL

Бренды по названию

Популярные бренды

Supermicro SuperServer 5019C-FL, Руководство пользователя

Результаты поиска

Содержание SuperServer 5019C-FL

Отзывы:

Похожие инструкции для SuperServer 5019C-FL

Бренды по названию

Популярные бренды