Supermicro SUPERSERVER 2028TR-H72FR Скачать руководство пользователя страница 78

Страница: 78 / 136

6-4

SUPERSERVER 2028TR-HTR/HTFR/H72R/H72FR User's Manual

Figure 6-4. Installing an Air Shroud

Note

: The figure is an example shroud and serverboard. Yours may differ slightly.

6-4 Air Shrouds

Air shrouds concentrate airflow to maximize fan efficiency. The SC217 chassis

requires air shrouds for each serverboard node. Air shrouds vary depending upon
the serverboard used. See the illustrations below.

Installing an Air Shroud

1. Cut a notch into the corner of the air shroud as shown below to allow more

airflow to cool the LSI 2208 chip.

2. Make sure that the serverboard expansion cards (if applicable) and all

components are properly installed in each serverboard node.

Place the first air shroud over the serverboard, as shown below. The air

shroud sits behind the system fans and goes over the top of the serverboard
and its components.

4. Repeat the procedure for the remaining node.

Air Shroud

Cut Notch

Содержание SUPERSERVER 2028TR-H72FR









































































































































Результаты поиска

Содержание SUPERSERVER 2028TR-H72FR

Отзывы:

Supermicro SUPERSERVER 2028TR-H72FR, Руководство пользователя, Страница: 78 / 136

Результаты поиска

Содержание SUPERSERVER 2028TR-H72FR

Отзывы: