manualshive.com logo in svg

Supermicro SUPERSERVER 2028TR-H72FR, Руководство пользователя, Страница: 16 / 136

Поделиться
Скачать
Supermicro SUPERSERVER 2028TR-H72FR Скачать руководство пользователя страница 16

1-6

SUPERSERVER 2028TR-HTR/HTFR/H72R/H72FR User's Manual

1-6  2U Twin

2

: System Notes

As a 2U Twin

2

 configuration, the SuperServer 2028TR-HTR/HTFR/H72R/H72FR is 

a unique server system. With four system boards incorporated into a single chassis 
acting as four separate nodes, there are several points you should keep in mind.

Nodes

Each of the four serverboards act as a separate node in the system. As independent 
nodes, each may be powered off and on without affecting the others. In addition, 
each node is a hot-swappable unit that may be removed from the rear of the chassis. 
The nodes are connected to the server backplane by means of an adapter card.

Note:

 A guide pin is located between the upper and lower nodes on the inner chassis 

wall. This guide pin also acts as a “stop” when a node is fully installed. If too much 
force is used when inserting a node this pin may break off. Take care to slowly slide 
a node in until you hear the “click” of the locking tab seating itself.

System Power

Dual 1600 power supplies are used to provide the power for all four serverboards. 
Each serverboard however, can be shut down independently of the other with the 
power button on its own control panel.

Hard Drive Backplane/Drives

The SuperServer 2028TR-HTR/HTFR/H72R/H72FR supports the use of 24 hard 
drives (SATA). A single backplane works to apply system-based control for power 
and fan speed functions and logically connects a set of six hard drives to each 
serverboard/node. Consequently, RAID setup is limited to a six-drive scheme (RAID 
cannot be spread across all 24 drives). See the Drive Bay Installation/Removal 

section in Chapter 6 for the logical hard drive and node configuration.

Adapter Cards

Besides the serverboard, the four servers are differentiated by the type of adapter 
card installed. The table below lists the differences between the four servers.

Server Differentiation

Server

Serverboard

Adapter Card

2028TR-HTR

X10DRT-H

BPN-ADPX9-6SATA-O-P

2028TR-HTFR

X10DRT-HIBF

BPN-ADPX9-6SATA-O-P

2028TR-H72R

X10DRT-H

BPN-ADP-S2208L-H6iR-O-P

2028TR-H72FR

X10DRT-HIBF

BPN-ADP-S2208L-H6iR-O-P

Содержание SUPERSERVER 2028TR-H72FR









































































































































Отзывы:

Нет отзывов