Supermicro Supero H8SME-F Скачать руководство пользователя страница 25

Страница: 25 / 72

Chapter 2: Installation

2-7

2-4 Mounting the Motherboard into a Chassis

All motherboards have standard mounting holes to fi t different types of chassis.

Make sure that the locations of all the mounting holes for both the motherboard

and the chassis match. Although a chassis may have both plastic and metal

mounting fasteners, metal ones are highly recommended because they ground

the motherboard to the chassis. Make sure that the metal standoffs click in or are

screwed in tightly.

Caution

: Some components are very close to the mounting holes. Please take

precautionary measures to prevent damage to these components when installing the

motherboard to the chassis.

Caution:

To avoid damaging the motherboard and its components, please do not use

a force greater than 8 lb/inch on each mounting screw during motherboard installation.

Checking the Compatibility of the Motherboard Ports and the I/O Shield

1. The H8SME-F motherboard requires a chassis that can support a board of

(LxW) 4.6" x 11.7" (116.84 x 297.18 mm) in size.

2. Make sure that the I/O ports on the motherboard align with their respective

holes in the I/O shield at the rear of the chassis.

Tools Needed

The following tools are needed to install the H8SME-F motherboard:

•

Phillps Screwdriver

•

Pan head screws (7 pieces)

•

Standoffs (7 pieces) (Only if needed)

Note:

The above items are not provided with this motherboard.

Location of Mounting Holes

There are seven (7) mounting holes on the H8SME-F motherboard. These holes

correspond to screw holes in a matching motherboard tray that slides into a blade-

type chassis. Please refer to the illustrations on the next page for a typical blade

chassis installation.

Содержание Supero H8SME-F









































































Результаты поиска

Содержание Supero H8SME-F

Отзывы:

Похожие инструкции для Supero H8SME-F

Бренды по названию

Популярные бренды

Supermicro Supero H8SME-F, Руководство пользователя

Результаты поиска

Содержание Supero H8SME-F

Отзывы:

Похожие инструкции для Supero H8SME-F

Бренды по названию

Популярные бренды