Supermicro SBI-7147R-S4F Скачать руководство пользователя страница 63

Страница: 63 / 84

5-11

Chapter 5: BIOS

Table 5-7. SCU Configuration Sub-menu

Menu Option

Description

Storage Controller
Unit

This setting allows you to

Enable

or Disable the chipset’s SCU devices. SMBus

0, 1, 2 will be disabled while SCU devices are disabled.

SCU RAID Option
ROM/UEFI Driver

This setting allows you to

Enable

or Disable using SCU RAID Option ROM for

your system.

Table 5-8. PCIe/PCI/PnP Configuration Sub-menu

Menu Option

Description

Launch Storage
OpROM Policy

This controls the excecution of UEFI and Legacy Storage OpROM in your
system. Options include

Legacy Only

or UEFI only.

PCI Latency Timer

This sets the value to programmed into the PCI Latency Timer Register. Options
include 32,

, 96, 128, 160, 192, 224 an 248.PCI Bus Clocks.

Above 4G Decoding

This setting allows you to Enable or

Disable

decoding of 64-bit capable devices

in the Above 4G Address Space. This setting is only usable if your system
supports 64-bit PCI decoding.

PERR# Generation

This setting allows you to Enable or

Disable

the PCI device to generate a

PERR#.

SERR# Generation

This setting allows you to Enable or

Disable

the PCI device to generate a

SERR#.

Maximum Payload

Use this setting to set the maximum payload of the PCI Express device or allow
the system BIOS to select the value. Options include

Auto

, 128 Bytes, 256

Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes or 4096 Bytes.

Maximum Read
Request

Use this setting to set the maximum read request size of the PCI Express device
or allow the system BIOS to select the value. Options include

Auto

, 128 Bytes,

256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes or 4096 Bytes.

ASPM Support

This sets the ASPM Level for your system. Options include

Disabled

(disables

ASPM), Auto (lets BIOS auto configure) or Force L0s (force all links to L0s state).

Onboard LAN Option
ROM Select

This setting allows you to select the onboard LAN option ROM to be either

PXE

or iSCSI. Note: If iSCSI is selected, LAN1 Option ROM select will cover all other
Oboard LANs.

Load Onboard LAN 1/
2 Option ROM

These settings

Enables

or Disables onboard option ROM for LAN1/2.

Load Onboard LSI
SAS (CPU1/2/3/4)
OPROM

These settings

Enables

or Disables loading onboard SAS option ROM.

VGA Priority

This setting decides the priority between onboard and 1st offboard video devices
found on your system. Options include

Onboard

or Offboard.

Network Stack

This setting allows you to Enable or

Disable

the network stack (Pxe and UEFI).

Содержание SBI-7147R-S4F





















































































Результаты поиска

Содержание SBI-7147R-S4F

Отзывы:

Похожие инструкции для SBI-7147R-S4F

Бренды по названию

Популярные бренды

Supermicro SBI-7147R-S4F, Руководство пользователя

Результаты поиска

Содержание SBI-7147R-S4F

Отзывы:

Похожие инструкции для SBI-7147R-S4F

Бренды по названию

Популярные бренды