background image

Chapter 1: Introduction

1-7

Notes

1. CPU Overclocking is supported by this motherboard; however, SMCI does not recommend CPU Overclocking and cannot 
resume any responsibility or liability of out_of_spec. overclocking.

2. CATERR_LED is for internal testing only.

Motherboard Features

CPU

Single Intel® C2000 Tri-Gate 22nm SoC (System-on-a 
Chip) Series processor in an FCBGA 1283 package 
Each SoC supports 4 cores or 8 cores
Refer to the table below for SoC support on MB model:

Memory 

Four (4) memory slots support up to 64 GB of DDR3 Unbuf-
fered (UDIMM) ECC or Non-ECC 1600/1333 MHz (1.5V, 
1.35V) memory

Note

: Please populate identical memory modules (of the 

same type/same speed/same frequency/same size) in all 
slots.
Dual-channel or single-channel w/x8 data width single-
rank/dual-rank memory

DIMM sizes

UDIMM

2 GB, 4 GB, 8 GB, and 16 GB

Expansion Slot 

One (1) PCI Express 2.0 x8 slot (Slot 6),
One (1) PCI Express 2.0 x4 slot (Slot 4)

Network Connections

C2000 SoC built-in I354  4-port GbE controllers (MACs) w/

Marvell 88E1543 Transceiver
Four (4) RJ-45 rear I/O panel connectors with Link and 

Activity LEDs, 

One (1) IPMI LAN connector (Realtek 8211E-PHY) 

I/O Devices

SATA Connections

SATA 3.0 (6Gb/s)

Two (2) SATA 3.0 (I-SATA 0/1) 

SATA 2.0 (3Gb/s)

Four (4) SATA 2.0 (I-SATA 2-5)

USB Devices

Four (4) USB 2.0 ports on the rear I/O panel (USB 0/1, 

2/3),

Two (2) USB 2.0 front accessible connector headers (USB 

4/5),

One (1) USB 2.0 Type A connector (USB 6)

Serial (COM) Ports

One (1) COM Port on the rear I/O panel (COM1)  

One (1)  front accessible Serial port header (COM2)

VGA (Graphics Display)

One (1) VGA Port on the rear I/O panel supported by the 

Aspeed AST 2400 VGA Controller

BIOS

128 Mb AMI BIOS

®

 SPI EEPROM BIOS

Plug and Play, DMI 2.3, PCI 2.3, ACPI 5.0, USB Keyboard, 

SMBIOS 2.7, and UEFI 2.3.1

Содержание A1SAM-2550F




































































































Отзывы: