SuperiorFireplaces.us.com
126861-01L
15
INSTALLATION
Continued
GLASS PEBBLE INSTALLATION
WARNING: Do not change or substitute glass
pebbles provided with this fireplace. If replacing, use
only replacement glass pebbles. See Parts
Page 27
.
WARNING: Do not block pilot ports with glass
pebbles.
WARNING: Do not place the glass pebbles on
the burner, only on the burner tray as illustrated in
Figure 25.
REPLACING LIGHT BULBS
1. Unplug power
2. Remove access door
(see
Figure 24, Page 14
).
3. Remove glass panel if installed
(see
Figure 25a
)
.
4. Remove rear interior wall
(see
Figure 21, Page 14
).
5. Remove glass Pebbles
(see
Figure 25
)
.
6. Remove six screws holding pebble pan.
7. Using a small slotted screwdriver, carefully slide it under edge
of light cover and pry it open.
8. Pull bulb out carefully and replace with bulb G9 120V/20W.
9. To replace, follow steps in the reverse order.
GAS CONTROL MODULE SYSTEM
The module has 2 special features built into the system.
Continuous Pilot Feature
This allows the change from a spark to pilot system to a standing
pilot system
1. There is a switch located on the right side of the module that reads
CONTINUOUS PILOT ON/OFF. This switch selects the pilot's mode of
operation
(
Figure 26
).
2. When the continuous pilot switch is in the OFF position and the appli-
ance rocker switch is turned ON, the pilot will spark and light. When
the appliance rocker switch is turned OFF, the pilot will shut OFF when
the main burner shuts OFF.
3. When the continuous pilot switch is in the ON position and the appli-
ance rocker switch is turned ON, the pilot will spark and light. When
the appliance rocker switch is turned OFF, the pilot will stay ON when
the main burner shuts OFF.
Figure 26 - Gas Module Right Side
Figure 27 - Gas Module Left Side
Remote Control Feature
The module has a built in remote control receiver that allows the
user to program the remote transmitter at any time during or after
the installation of the burner.
1. There is a switch located on the right side of the module that reads
REMOTE/OFF
(
Figure 27
).
2. When the remote/off switch is in the OFF position, the burner will
operate from the rocker switch or wall switch connected to the
two BROWN wires on the module.
3. When the remote/off is in the REMOTE position the burner will
operate from the Remote Control transmitter.
Figure 25a - Installing/Removing Glass Panel
Clear glass pebbles are included with your fireplace. Install the glass
pebbles before installation of optional Draft Shield Kit, LV43DS
(F1031).
1. Place glass pebbles in a single layer evenly on the pebble pan.
Make certain that the correct media is used. If crushed glass
or other media is used, replaced it with the proper media listed
on the price list. Make certain the media is placed precisely as
indicated in this instruction manual (single layer of pebbles in
straight rows) and all glass remains on the pebble tray with no
glass at all on the burner.
OPTIONAL DRAFT SHIELD KIT INSTALLATION (F1031)
Note:
Barrier kit cat. no. F2882 is required when installing this kit.
The glass panel assembly should be installed after the fireplace is
completely framed and finished. The brackets are attached to the front
side face of the fireplace using two screws as shown in
Figure 25a.
Position the glass panel in the bracket so that it is securely in place.
Continuous Pilot
Off/On Switch
Remote/Off
Switch
“S” Pilot
Connection
“I” Pilot
Connection
ADJ.
Figure 25 - Placing Glass Pebbles
Place Glass
Pebbles on the
pebble tray in a
single orderly
layer.
Glass Panel
Bracket
Screws
Learn Button
AUX Connection
