background image

26

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS  •  POWER VENT DV GAS FIREPLACES  (DRT6340/45TYN)  •  INSTALLATION INSTRUCTIONS

Only doors certified with the appliance 

shall be used.

Seules des portes certifiées pour cet 

appareil doivent être utilisées.

WARNING: DO NOT abuse glass door by 

striking or slamming shut.

Step 11. BURNER ADJUSTMENTS 

Flame Appearance and sooting

Proper flame appearance is a flame which is blue 

at the base and becomes yellow-orange in the 

body of the flame. When the appliance is first lit, 

the entire flame may be blue and will gradually 

turn yellow-orange during the first 15 minutes 

of operation. After 15 minutes of operation, if 

the flame is blue, or if the flame is orange with 

evidence of sooting (black tip), the air shutter 

opening may need to be adjusted.
If the air shutter opening is closed too far, 

sooting may develop. Sooting is indicated by 

black puffs developing at the tips of very long 

orange flames. Sooting results in black deposits 

forming on the logs, appliance inside surfaces 

and on exterior surfaces adjacent to the vent 

termination. 

Sooting is caused by incomplete combustion 

in the flames and lack of combustion air enter-

ing the air shutter opening. To achieve a warm 

yellow-orange flame with an orange body that 

does not soot, the shutter opening must be 

adjusted between these two positions. 

Air Shutter Adjustment Guidelines

•  If there is smoke or soot present, first check 

the log set positioning to ensure that the 

flames are not impinging on any of the logs. 

If the log set is properly positioned and a 

sooting condition still exists, then the air 

shutter opening should be increased.

•  The more offsets in the vent system, the larger 

the air shutter opening will need to be.

WARNING: Any safety screen or guard re-

moved for servicing the appliance must be 

replaced prior to operating the appliance.

AVERTISSEMENT : Tout écran ou pro-

tecteur retiré pour permettre l’entretien de 

l’appareil doit être remis en place avant 

de mettre l’appareil en marche.

Installing Glass Enclosure Panel
(see Figure 40)

To install the front glass door assembly, proceed 

as follows:
1.   Retrieve the glass door assembly. Visually 

inspect the gasket on the backside of the 

panel. The gasket surface must be clean, 

free of irregularities and seated firmly.

2.    Position the door frame in front of the firebox 

opening and engage the bottom flange over 

the rail at the bottom of the firebox opening.

3.   Swing the door up and back. Ensure the 

gasket seats evenly as the door draws shut. 

Engage the nut insert and fasten with two 

screws to secure the door.

4.  Install the door modesty shield on top 

flange glass door as follows: grab the door 

modesty shield with both hands, with the 

open hem going down and engage it with 

the upper lip of the glass door frame by 

pushing it all the way down. Make sure the 

installed shield is firmly in place.

WHEN INSTALLING THE GLASS DOOR, SE-

CURELY TIGHTEN THE LATCH SCREWS - SEE 

THE FIRST WARNING ON THIS PAGE.

Step 10. INSTALLATION AND REMOVAL 

OF GLASS DOOR

       WARNING 

• When reinstalling the glass 

door, the door latch screws 

must be securely tightened 

to prevent the glass door 

from falling out, which could 

potentially cause damage and 

possible injury.

• Do not attempt to substitute the 

materials used on this door, 

or replace cracked or broken 

glass. 

• Handle this glass with extreme 

care! Glass is susceptible to 

damage - Do not scratch or 

handle roughly while reinstall-

ing the glass door frame.

• The glass door of this appli-

ance must only be replaced 

as a complete unit as provided 

by the manufacturer. Do not 

attempt to replace broken, 

cracked or chipped glass sepa-

rately. 

• Do not attempt to touch the 

front enclosure glass with your 

hands while the fireplace is in 

use.

       WARNING 

Do not operate appliance with 

the glass front removed, cracked 

or broken.

       AVERTISSEMENT 

Ne pas utiliser l'appareil si le 

panneau frontal en verre n'est 

pas en place, est craqué ou 

brisé. 

Top Flange Glass door 
assembly

Glass Door Latch (2)

Glass Door Assembly

Firebox Floor

Figure 40 - Installing the Glass Door

Latch 
Screws

When installing the glass door, ensure 
the spacing on both sides are equal.

Barrier (see Notice, Page 40)

This fireplace comes with a barrier to reduce the 

likelihood of burns from touching hot glass. If 

the barrier is damaged, the fireplace should be 

turned off immediately and the fireplace must 

not be operated until a new, approved factory 

barrier for this unit is installed.

To remove barrier follow these steps.

1.Lift barrier up by the frame at the top.

2.Remove lower filler piece by pulling down  

   off of the barrier.

3.Lower barrier and push barrier to left to 

   release right side.

4.Pull the right side out of fireplace.

5.Remove barrier.

6.  Install  the  new,  approved  factory  barrier  with            

flat side of barrier toward firebox.

Содержание Signature DRC6340TYN



























































Отзывы: