Super X8DT6 Скачать руководство пользователя страница 86

Страница: 86 / 99

4-24

X8DT6/X8DT6-F/X8DTE/X8DTE-F

User’s Manual

Password Check

This item allows you to check a password after it has been entered.

The options

are

Setup

and Always.

Boot Sector Virus Protection

When Enabled, the AMI BIOS displays a warning when any program (or virus) is-

sues a Disk Format command or attempts to write to the boot sector of the hard

disk drive. The options are Enabled and

Disabled

4-5 Boot Confi guration

Use this feature to confi gure boot settings.



Boot Device Priority

This feature allows the user to specify the sequence of priority for the Boot Device.

The settings are 1st boot device, 2nd boot device, 3rd boot device, 4th boot device,

5th boot device and Disabled.

1st Boot Device - 1st Floppy Drive

•

2nd Boot Device - [USB: XXXXXXXXX]

•



Hard Disk Drives

This feature allows the user to specify the boot sequence from all available hard

disk drives. The settings are Disabled and a list of all hard disk drives that have

been detected (i.e., 1st Drive, 2nd Drive, 3rd Drive, etc).

Содержание X8DT6




































































































Результаты поиска

Содержание X8DT6

Отзывы:

Похожие инструкции для X8DT6

Бренды по названию

Популярные бренды

Super X8DT6, Руководство пользователя

Результаты поиска

Содержание X8DT6

Отзывы:

Похожие инструкции для X8DT6

Бренды по названию

Популярные бренды