Super X8DT6 Скачать руководство пользователя страница 32

Страница: 32 / 99

2-10

X8DT6/X8DT6-F/X8DTE/X8DTE-F User's Manual

1.35V DIMMs

•

1.35V RDIMM Population for the Motherboard w/5600 Processors Installed

DIMM
Slots per
Channel

DIMMs
Populated
per Channel

DIMM Type
(Reg.=Registered)

Speeds (in MHz)

Ranks per DIMM
(any combination;
SR=Single Rank,
DR=Dual Rank,
QR=Quad Rank)

Reg. DDR3 ECC

800,1066,1333

SR or DR

Reg. DDR3 ECC

800 (Note 1)

Reg. DDR3 ECC

800,1066 (Note 2)

Mixing SR, DR

Reg. DDR3 ECC

800 (Note 3)

Mixing SR, DR, QR

Note 1:

1333/1066 MHz QR RDIMMs will run at 800 MHz (-BIOS automatic downgrading).

Note 2:

1333 MHz SR/DR RDIMMs will run at 800 MHz (-BIOS automatic downgrading).

Note 3:

1333/1066 MHz SR/DR/QR RDIMMs will run at 800 MHz (-BIOS automatic downgrading).

Note 4:

Mixing of 1.35V and 1.5V DIMMs is not recommended.

1.35V UDIMM Population for the Motherboard w/5600 Processors Installed

DIMM
Slots per
Channel

DIMMs
Populated
per Channel

DIMM Type (Unb.=
Unbufered)

Speeds (in MHz)

Ranks per DIMM
(any combination;
SR=Single Rank,
DR=Dual Rank,
QR=Quad Rank)

Unb. DDR3 ECC

800,1066,1333

SR or DR

Unb. DDR3 ECC

800,1066

Mixing SR, DR

Note 1:

1333 MHz for two DIMMs per channel is supported when Unbuf./ECC DIMMs are used.

Note 2:

Mixing of 1.35V and 1.5V DIMMs is not recommended.

Notes: 1

: Due to OS limitations, some operating systems may not show

more than 4 GB of memory.

: Due to memory allocation to system de-

vices, the amount of memory that remains available for operational use

will be reduced when 4 GB of RAM is used. The reduction in memory

availability is disproportional.

Possible System Memory Allocation & Availability

System Device

Size

Physical Memory (4 GB Total memory)
Remaining (-Available)

Firmware Hub fl ash memory (System BIOS)

1 MB

3.99 GB

Local APIC

4 KB

3.99 GB

Area Reserved for the chipset

2 MB

3.99 GB

I/O APIC (4 Kbytes)

4 KB

3.99 GB

PCI Enumeration Area 1

256 MB

3.76 GB

PCI Express (256 MB)

256 MB

3.51 GB

PCI Enumeration Area 2 (if needed) -Aligned on
256-MB boundary-

512 MB

3.01 GB

VGA Memory

16 MB

2.85 GB

TSEG

1 MB

2.84 GB

Memory available for the OS & other applications

2.84 GB

Содержание X8DT6




































































































Результаты поиска

Содержание X8DT6

Отзывы:

Похожие инструкции для X8DT6

Бренды по названию

Популярные бренды

Super X8DT6, Руководство пользователя

Результаты поиска

Содержание X8DT6

Отзывы:

Похожие инструкции для X8DT6

Бренды по названию

Популярные бренды