manualshive.com logo in svg

Super Systems PGA 3510, Руководство по эксплуатации, Страница: 41 / 42

Поделиться
Скачать
Super Systems PGA 3510 Скачать руководство пользователя страница 41

PGA 3510 Operations Manual 

Super Systems Inc.                      

 

 

 

Page 41 of 42 

 

 

Appendix 1: PGA 3510 Common Modbus Registers 

 

This appendix covers Modbus registers most commonly accessed by PGA 3510 users. These are Modbus 

registers 200 through 227 and their descriptions. There are other Modbus registers used by the PGA 

3510. If you need information on other registers, call SSi at (513) 772-0060. 

 

Register Location 

Parameter 

Description 

200 

co_data 

Measured CO value 

201 

co2_data 

Measured CO

2

 value 

202 

o2_data 

Measured 0

2

 value 

203 

ch4_data 

Measured CH

4

 value 

204 

Bench_off 

Turn off bench, pump, and sample 

205 

IR_carbon 

IR %C 

206 

IR_COF 

Suggested COF (CO Factor) 

207 

IR_PF 

Suggested PF (Process Factor) 

208 

IR_MV 

IR equivalent millivolts 

209 

probe_MV 

Probe millivolts 

210 

probe_COF 

Probe COF 

211 

probe_temperature 

Probe temperature 

212 

probe_PF 

Probe PF 

213 

probe_carbon 

Probe %C 

214 

pump_run_min 

The total time in minutes that the 

pump has run since the last time 

memory was cleared or a manual 

reset took place. This value, plus 

pump_run_wks, will provide the total 

amount of time the pump has been 

running. When this number reaches 

10080, pump_run_wks is increased by 

1, and pump_run_min is reset to zero.  

215 

pump_run_wks 

The total time in weeks that the pump 

has run since the last time memory 

was cleared or a manual reset took 

place. This value, plus pump_run_min, 

will provide the total amount of time 

the pump has been running. 

216 

pump 

Pump status 

217 

pump_run_now 

The time in minutes that the pump is 

running (reset to zero if pump is 

turned off). Maximum value is 30000. If 

pump_run_now is greater than 

pump_run_max, then pump_run_max 

is set to pump_run_now. 

218 

pump_run_max 

The longest time in minutes of a pump 

session. If pump_run_now is greater 

than pump_run_max, then 

pump_run_max is set to 

pump_run_now. 

219 

calib_status 

Calibration status 

220 

IR_temperature 

IR temperature 

221 

output_percent 

Control output in percent 

222 

sample_flow 

Sample flow 

Содержание PGA 3510











































Отзывы:

Нет отзывов