Supaswift SSU420ACM Скачать руководство пользователя | Manualshive

Страница: 13 / 22

background image

13

WARNING

Ensure engine is stopped before making any adjustment. The engine

switch must be in “OFF” position and spark plug lead disconnected.

!

It will become necessary to reset the blade after continued use. The rotating blade is correctly adjusted when it is
lightly touching the bottom blade.

BLADE SETTING

1.

Empty the fuel tank.

2.

Ensure engine is switched off and spark plug lead is disconnected.

3.

Tilt the mower back on its handles.

4.

Slip a piece of paper between rotational blade and the bottom blade.

5.

Turn the rotational blade. If the blade cuts the paper it is adjusted correctly.

6.

Repeat the process at several points along the blade.

CHECKING THE BLADE SETTING

«
...
11
12
13
14
15
...
»

Содержание SSU420ACM























Отзывы:

Нет отзывов

Похожие инструкции для SSU420ACM

Бренд: Poulan Pro Страницы: 30

Бренд: Peco Страницы: 12

Бренд: Cadet Страницы: 44

Бренд: Scag Power Equipment Страницы: 42

Бренд: Snapper Страницы: 2

Бренд: Yard-Man Страницы: 11

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Ferris Страницы: 60

Бренд: RHINO Страницы: 160

Бренд: dormak Страницы: 24

Бренд: Worx Страницы: 10

LANDROID WG757E

Бренд: Worx Страницы: 21

LANDROID L WG792E

Бренд: Worx Страницы: 20

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 8

Бренд: Honda Страницы: 24

Бренд: MTD Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды