SunStar KM-857J Series Скачать руководство пользователя страница 38

Страница: 38 / 38

Symptom

Checkpoints

Root cause

Corrective action

After trimming, lower thread holder
does not hold the lower thread

Due to problems in the up-stop
position of the needle, the thread
take up lever pulls the upper thread
out of the needle when the sewing
starts

The upper thread oil felt is pressing
the thread too strongly.

The height and distance between
the movable knife and the hook do
not match

Tension and contact of movable
and fixed knives are bad

Needle is not inserted correctly

Scratch and abrasion of movable
and fixed knives

The timing of trimming cam is
wrong

Thread release stroke is too small

Wrong trimming timing

The opening on the thread tension
control plate is too small

Too strong tension on the auxiliary
thread tension control assembly

Thread take up stroke is too large

Volume is adjusted to too low

Adjust the location and tension of
the lower thread holder.

Readjust the needle’s up-stop film
position

Adjust the felt tension

Readjust the movable knife setting
position

Correct the tension adjustment and
surface contact of movable and
fixed knives.

Insert the needle correctly

Replace movable knife or fixed
knife.

Adjust the timing of trimming cam

Readjust the thread release stroke

Adjust the trimming timing

Adjust the thread release stroke

Adjust the tension of the auxiliary
thread tension control assembly

Adjust the thread take up spring’s
stroke

Increase the volume adjustment.

Lower thread holder

Check the up-stop
position of the needle

Check the oil felt
tension of upper
thread

The gap between the
movable knife and
the hook

Check the tension of
fixed knife

Direction of the needle

Blade side of movable
and fixed knives

Trimming cam timing

Thread release stroke

Trimming timing

Opening of the thread
tension adjusting plate

Tension of auxiliary
thread tension
adjustment assembly

Thread take up stroke

Thread release
adjustment volume
on the control box

Upper thread
falls out when
starting to sew
or sewing is
skipped.

Trimming miss

Too short
thread length
after trimming

Remaining upper
thread length after
trimming

The length of the remaining upper
thread is too short

Increase the adjustment volume of
the upper thread on the control box

Содержание KM-857J Series







































Результаты поиска

Содержание KM-857J Series

Отзывы:

Похожие инструкции для KM-857J Series

Бренды по названию

Популярные бренды

SunStar KM-857J Series, Руководство пользователя

Результаты поиска

Содержание KM-857J Series

Отзывы:

Похожие инструкции для KM-857J Series

Бренды по названию

Популярные бренды