SunStar KM-857J Series Скачать руководство пользователя страница 30

Страница: 30 / 38

(3) Adjusting movable knife and fixed blade(See figure 45)

A) Adjusting the position of movable knife and hook

a) As in picture

unfasten the movable knife fixing

screw

③

to adjust the movable knife so that the

edge of the movable knife

①

sits at the very center

of the hook’s

②

V-shaped groove. Tightly fasten

after sideway adjustment.

b) Adjust the distance between the movable knife

①

and the upper side of the hook

②

to be 0.5mm.

※

To adjust, unfasten the clamp screw

⑤

of the

hood shaft gear and the clamp screw

④

of the

movable knife shaft collar. Vertically adjust the

movable knife shaft

⑥

, and then tightly fasten the

clamp screws

④⑤

[Figure 45]

B) Adjusting movable and fixed knife (See figure 46)

a) Like in figure 46, manually operate the movable knife

①

and then slowly reposition it in its original place. Now,

just like in the figure, place the fixed knife so that the fixed knife

③

edge

④

touches 3mm before the movable

knife’s trimming point

②

b) Match the upper side of the fixed blade

③

and movable knife

①

. Fully adhere the upper

and lower

parts of

the fixed blade edge with the outer side of the movable knife edge.

c) Under this condition, tightly fasten the fixed blade clamp screw

⑤

. Be careful so that the fixed blade does not

move.

d) Once the adjustment is complete, operate manual trimming once again to check the crossing of the movable and

fixed knives crossing.

[Figure 46]

②

①

⑥

③

④

⑤

0.5mm

①

③

④

②

Trimming point

3mm

Fixed knife base point

①

③

⑤

Matching upper side

※

The crossing between movable
knife and fixed blade.

(Good)

(Bad)

Содержание KM-857J Series







































Результаты поиска

Содержание KM-857J Series

Отзывы:

Похожие инструкции для KM-857J Series

Бренды по названию

Популярные бренды

SunStar KM-857J Series, Руководство пользователя

Результаты поиска

Содержание KM-857J Series

Отзывы:

Похожие инструкции для KM-857J Series

Бренды по названию

Популярные бренды