7
Programming Table Ver:1.03
Connect a Single-Line Phone and
hang up
.
Press and hold on [P]
key then
plug in power
2 LED Blinking slowly.
Lift handset
(or press [HOOK] key if have).
2 LED keep light and waiting for a long Beep.
Input security
Password(
Default is
1234)
2 LED keep dark waiting for a long Beep..
Dial the
ITEM and IMMEDIATELY the data
which you want to store in.
IF want to clear all data before programming please dial *0 and waiting for a long Beep
ITEM
Description
Actual data
Digits
(Digit 1)
1
st
Prefix
P: None
1-#=prefix
(Digit 2)
2
nd
Prefix
P: None
1-#=prefix
(Digit 3)
Total digits of prefix
included 1
st
& 2
nd
Max. 8 digits
(Digit 4)
Send just received
prefix or not?
1:yes 0:no
1
(Digit 5)
Total digits of
user’s password
max. 8 digits
(Digit 6)
Send just
received user’s
password or not
1:yes 0:no
(Digit 7)
Send stored user’s
password to system
or not?
P= no, 1-*#=yes,
also send this code
(Digit 8)
When to send stored
user ‘s password?
0: before send Item4
1: before send Item5
2: before send Item8
8
2 First system’s
Trigger code,
should be international prefix e.g. 011 in USA.
(Input * means accept any code, Input 0P means for tolling call)
4
3 First system’s
Access No
.
/
Clear if access ISR
16
4 First system’s
PIN code
and/or password.
/
Clear if access ISR
16
5 First system’s
Destination prefix
/
ISR access prefix
e.g. 18XXX
16
6
First system’s
Backup access No.
In case of unreachable.
16
7
First system’s
extra Trigger code.
e.g. 01*
4
8 First system’s
Destination suffix.
e.g. #
/
Clear if access ISR
8
9 Security Password for entry programming mode. Dialer will auto-backup
current password when set it. Next time you may use new or old password, if
you want keep only one please set this twice.
(please don't forget!)
IMPORTANT
Fixed 4
digits
0
Exceptant code
. Per code add * to wait beep and input next code.
e.g. 86*---84*---323*---673*--- ---(Waiting another beep to finish if no more)
4digits/
20 sets
# (Digit
1)
DTMF duration time
*
= 50mS, #=60mS
0= 70mS, 1=100mS
2=150mS, 3=200mS
(Digit 2)
FLASH TIME
1=100mS
2=200mS
3=300mS,...
(Digit 3)
Remote prog.
0= Enable
1= Disable
(Digit 4)
Waiting time to stop.
Not divert call=1S
Divert call=3S
1=4S,2=3S,3=2S
4
*
9
Prefix code when active Special function by dial * (see item *# digit 2)
8
**
Pre-set user’s password for dialer to verify. Per password add * to wait beep
and input next password. e.g. 123*---456*---323*---673*--- ---
4digits/
48 sets
(Digit 1)
Force pass Code
E.g. #
(Digit 2)
Trigger code for
active special
function.
E.g. *
(Digit 3)
Connect line and phone
after all dialed?
0=Yes 1=No
#=yes, but wait #,A,B,C
(Digit 4)
Tone/Pulse dialing
(Dial item 3 only)
0=DTMF
1=PULSE
*
#
(Digit 5)
Connect line and
phone in standby
mode?
0=Yes 1=No
(Digit 6)
N/A
(Digit 7)
N/A
(Digit8)
N/A
8
*27
First system’s
2
nd
extra Trigger code.
e.g. 02*
4
*37
First system’s
third Trigger code.
4
*47
(Digit 1)
Extra trigger check sequence
0=Immediately after checked
first item 2
1=Checked every item 2 then
check e
xtra trigger
(Digit 2)
Time to release line
when unreachable
No=0.8S
1=1S, 2=1.2S, 3=1.4S...
(Digit 3)
N/A
(Digit 4)
N/A
4
1=When extra trigger (item 7) set 01*, but have normal trigger (item 2) set to 011. Code confusing
0=When extra trigger (item 7) set 01*, but have normal trigger (item 2) set to 0P. Code confusing
