Quickie
®
Q700-UP M Seating Manual
247556 Rev. B
20
7.0 USING THE SEATING SYSTEM
7.6 Electric standing function
The Quickie Q700-UP M has an electric standing function. This function makes it
possible for the user to stand in the wheelchair.
DANGER!
The use of knee fi xation and chest straps are mandatory when using the standing
function.
WARNING!
1.
Before using the standing function ensure that the chest belt is secure.
2.
Before using the standing function ensure that the front knee fi xation is in
place.
3.
Only use the standing function on a sound and level surface.
4.
The standing procedure automatically locks the front and rear caster arm
suspension.
5.
If the locking procedure fails the chair will automatically stop in a safe
position. The seat can always be returned to the normally seated position in
any mode. Potential causes could be damage to the harnesses or incorrect
assembly placement.
DANGER!
When the standing, or lie down function is used, the center of gravity is moved
away from the original safe position into a raised or retracted position. This can
increase the likelihood of tipping over. So only use this seat function on a level
fl oor and drive in the lowest speed. Not doing so could lead to personal
injury.
7.7 Seat memory position
The control system on the Q700-UP M has up to 6 predefi ned seat memory
positions. Each ordered memory location has a set of factory seat positioning
presets:
1.
Seated
2.
Supine
3.
Pressure Relief
4.
Forward Tilt
5.
Transfer
6.
Stand
The seat actuators are all working with a feedback system to track their
positions and movements.
This is important:
1.
To reach the required memory position.
2.
To prevent mechanical clashes of the seat.
3.
To operate the actuators especially towards the memory positions in an
ergonomic, smooth, and safe way.
All ordered memory positions, if not suitable for the user, can be changed and
customized to the needs required. The software takes into account the range of
the available mechanical movements and also all safety aspects.
7.7.1 Retrieving a memory seat position (Fig. 7.8 - 7.10)
1.
Press the ”Mode” button (A) one or more times until a seat icon appears in
the LCD control panel display.
2.
Move the joystick to the left or right to select a memory seat position:
a.
Seated
b.
Supine
c.
Pressure Relief
d.
Forward Tilt
e.
Transfer
f.
Stand
A seat icon and the memory description or the relevant position are shown
in the LCD control panel display.
3.
Move and hold the joystick forwards. The seat adjusts to the factory preset
position. The movement can be stopped at any time and started again when
moving the joystick forward.
4.
In any of the 6 memory seat positions moving the joystick backwards brings
the seat into the “Seating” memory position. Once the seat has adjusted to
the saved position, it stops moving.
Note:
1.
Movement of the seat can be stopped at any time by releasing the joystick.
2.
During a stop period, another memory position can be selected with a right
or left movement of the joystick. After selecting a new memory position,
moving the joystick forward will operate the seat into the new selected
position.
7.7.2 Return to drive mode
Press the ”Mode” button one or more times until a standard display image with
speed indicator appears in the LCD control panel display.
7.7.3 Saving a new position to memory
1.
Remove the rear cover of the backrest and connect a Switch with a 3.5mm
Jack to the socket on the CxSM. (Fig. 7.11)
2.
Press the “mode” button one or more times until a seat icon appears in the
LCD control panel display. (Fig. 7.12)
3.
Move the joystick to the left or right to select a memory seat position
(Fig. 7.13). A seat icon and the memory description or the relevant
position are shown in the LCD control panel display. (Fig. 7.12)
4.
Move and hold the joystick forwards (Fig. 7.13). The seat adjusts to the
factory preset position. The movement can be stopped at any time and
started again when moving the joystick forward.
5.
Stop the seat movement where required and select with a left or right
joystick movement the seat actuator that needs to be changed.
6.
Move the joystick forward or backwards until the required position is
reached. Select other actuators if required and move them where needed.
7.
Move the joystick left or right until the factory memory position is reached
and where the new position shall be programmed in.
8.
Press and hold the switch connected to the CxSM (Fig. 7.10) and pull the
joystick backwards for 3 seconds until a beep can be heard.
9.
Release the joystick and the button. Your new required position is now
stored and the actuators will always stop in this new programmed end
position.
Fig.7.8
Fig.7.9
Fig.7.10
