V+ V+
CW- CW-
WW- WW-
V+ V+
CW- CW-
WW- WW-
AC Power
50/60Hz
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible
systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee
system.
3. Zigbee Network Pairing through Coordinator or Hub
(
Added
to
a
Zigbee
Network
)
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) To control by both gateway & remote, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
Step 1
: Remove the device from previous zigbee network if it has already been added to
,
otherwise
pairing
will
fail
.
Please
refer
to
the
part
"
Factory
Reset Manually
".
Step 2
: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3
: Re-power on the device to set it into network pairing mode (connected light flashes twice slowly), 15
seconds timeout, repeat the operation.
Step 4
: Connected light will blink 5 times and then stay
solid on, then the device will appear in your controller's
menu and can be controlled through controller or hub
interface.
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset the
lighting device as instructed. The connected light blinks 3 times to indicate
successful reset.
Step 4
: There shall be indication on
the remote for successful link and
connected light will flash twice.
< 10cm
Zigbee
Remote
Step 2
: Bring the remote or touch panel within 10cm of the lighting device
.
Step 3
: Set the remote or touch panel into Touchlink commissioning,
please refer to corresponding remote or touch panel manual to learn how
.
6. Factory Reset Manually
Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.
Step 1
: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if
the “Prog.” key is not accessible.
Step 1
: Re-power on the device to start TouchLink Commissioning, 180 seconds timeout, repeat the operation.
7. Factory Reset
through
a
Zigbee
Remote (Touch Reset)
Note
: Make sure the device already added to a network, the remote added to the same one or not added to any
network.
Step 2
: Bring the remote or touch panel within 10cm of the lighting device
.
Step 3
: Set the remote or touch panel into Touch Reset procedure to reset the
device, please refer to corresponding remote or touch panel manual to learn how
.
Step 2
: Connected light will blink 3 times to indicate
successful reset.
Step 4
: There shall be indication on
the remote and connected light
flashes 3 times for successful reset.
< 10cm
Zigbee
Remote
AC Power
50/60Hz
AC Power
50/60Hz
AC Power
50/60Hz
V+ V+
CW- CW-
WW- WW-
V+ V+
CW- CW-
WW- WW-
4. TouchLink
to
a
Zigbee
Remote
Step 1: Method 1
: Short press “Prog” button 4 times (or re-power on the device 4 times) to start Touchlink
commissioning immediately, 180S timeout, repeat the operation.
Method 2
: Re-power on the device, Touchlink commissioning will start after 15S if it’s not added to a zigbee
network, 165S timeout. Or start immediately if it’s already added to a network, 180S timeout. Once timeout,
repeat the operation.
LED+
WW-
CW-
ZigBee LED Driver
S
E
LV
Prog key
A
C I
N
P
U
T
NC
NC
1 2 3 4 5 6 7 8
Push Switch Input
LED+
WW-
CW-
ZigBee LED Driver
S
E
LV
Prog key
A
C I
N
P
U
T
NC
NC
1 2 3 4 5 6 7 8
Push Switch Input
LED+
WW-
CW-
ZigBee LED Driver
S
E
LV
Prog key
A
C I
N
P
U
T
NC
NC
1 2 3 4 5 6 7 8
Push Switch Input
LED+
WW-
CW-
ZigBee LED Driver
S
E
LV
Prog key
A
C I
N
P
U
T
NC
NC
1 2 3 4 5 6 7 8
Push Switch Input
