Sunricher SR-ZG9101SAC-HP-SWITCH, Инструкции

Страница: 1 / 4

AC ZigBee In-wall Switch
09.ZG09SAP.04736
Function introduction
Important: Read All Instructions Prior to Installation
“Reset” Key: for
network pairing,
touchlink, factory
reset of the switch,
turn on/off the load
AC 100-240V power input
pu
sh
sw
itc
h
L L N N
OUT
A1-A2: 8-230V
AC 100-240V
1 CH 100-240VAC output
•
ZigBee in-wall switch based on latest ZigBee 3.0 protocol
•
100-240VAC Wide Input and Output Voltage
•
Supports resistive loads and capacitive loads
•
1 Channel Output, Up to 400W
•
Input and Output with Screw Terminals, Safe and Reliable
•
Enables to control ON/OFF of connected load
• ZigBee end device that supports Touchlink commissioning
•
Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
•
Supports self-forming zigbee network without coordinator and add other devices to the network
•
Supports find and bind mode to bind a ZigBee remote
•
Supports zigbee green power and can bind max. 20 zigbee green power remotes
•
Compatible with universal ZigBee gateway products
•
Can be controlled by universal 8-230V input single wire push switch
•
Mini Size, Easy to be Installed into a standard 86*86mm wall box
•
Radio Frequency : 2.4GHz
• Waterproof grade: IP20
Reset
LED indicator
Input Voltage Output Voltage Output Current
Product Data
Size(LxWxH)
Compatible Load Types
Load Symbol Load Type Maximum Load Remarks
Due to variety of LED lamp
designs, maximum number
of LED lamps is further
dependent on power factor
result when connected to
switch.
Maximum permitted number
of drivers is 200W divided
by driver nameplate power
rating.
LED lamps with transformers
LED drivers
Incandescent lighting,
HV Halogen lamps
Low voltage halogen
lighting with electronic
transformers
100-240VAC 1.8A max 100-240VAC 45.5x45x20.3mm
200W @ 220V
100W @ 110V
200W @ 220V
100W @ 110V
400W @ 220V
200W @ 110V
200W @ 220V
100W @ 110V
•
DO NOT install with power applied to device.
•
DO NOT expose the device to moisture.
Safety & Warnings
Operation
1.Do wiring according to connection diagram correctly.
3. Zigbee Network Pairing through Coordinator or Hub
(
Added to
a
Zigbee Network
)
Step 1 : Remove the device from previous zigbee network if it has already been added to , otherwise pairing will
fail
.
Please refer to the part
"
Factory Reset Manually
".
Step 2 : From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 3 : Reset power of the device to
set it into network pairing mode
(connected light flashes twice
slowly), 15 seconds timeout, repeat
this step.
Step 4 : Connected light will blink 5
times and then stay solid on, then the
device will appear in your controller's
menu and can be controlled through
controller or hub interface.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This
receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
ZigBee Clusters the device supports are as follows:
Input Clusters
0x0000: Basic 0x0003: Identify 0x0004: Groups 0x0005: Scenes 0x0006: On/off
0x0b05: Diagnostics
Output Clusters
0x0019: OTA
L
N
pu
sh
sw
itc
h
L L N N
OUT
L
N
A1-A2: 8-230V
AC 100-240V
Reset