Sunnydaze Decor WAR-840 Скачать руководство пользователя страница 14

MAINTENANCE

Before performing any maintenance always disconnect propane gas tank.

Keep the heating item free and clear from combustible materials.

Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.

Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and 

lava rocks

are completely cooled down. Wipe down with a soft cloth.

Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.

Permanent damage may occur if powder or solvent comes in contact with painted or plastic

components on this heating unit.

Keep the heating unit stored away from direct sunlight.

If storing this unit inside, disconnect the propane gas tank from the gas valve.

Not using manufacturer approved or supplied parts/accessories may result in a defective condition

and void the warranty of this heating unit.

Always place lid (if applicable) or protective cover on heating item when not in use.

MGO 

Surface Care

Our 

MGO

 material has been sealed with a 

special 

treatment to prevent staining and moisture 

absorption, but it does require proper maintenance to ensure the integrity of the surface. Please 

see below for recommendations on maintaining your 

MGO

 

surface for years of pleasure:

• Clean any spills immediately to p

r

event permanent 

MGO 

surface staining or damage.

Blot any liquid spills with a clean, dry cloth to avoid spreading of the spill to the rest of the table.
Clean your 

product

 

surface with a soft, clean cloth or sponge. Mix a solution of warm clean water

and mild dish soap to remove any surface dirt or mild spills. Rinse all soap solution off of the
tabletop and dry completely to avoid water spots. Regularly cleaning the surface will aid in a
longer lasting product.

• Do not use pet oleum-based or abrasive cleaning products. Do not use any harsh brushes when

cleaning the surface.

• Do not slide p

r

oducts across the surface to avoid permanent scratching and damage.

• Always use p

r

otective mats such as coasters or placemats when eating on an 

MGO surface.

These protective products will help absorb sweating on cool beverages and will block out any
heat rings from appearing beneath a warm mug or plate. When placing hot dishes on 

MGO

surface, always use mats or hot pads.

MGO 

surface must be covered at all times when not in use. Cover your product with an

outdoor furniture cover when not in use to protect it from the elements. Store your product
indoors during winter months. Avoiding extreme cold temperatures will prevent cracking of the
tabletop.

14

Содержание WAR-840


















Отзывы: