background image

14.) 

To lock the 

(PART B) SIDE PANELS

 in 

place,  hold 

(PART  B)  SIDE  PANEL

  in  the 

upright position.  Rotate the 

“side panel lock 

lever”

  from  the  upright  position,  to  the 

downward position.  Be sure to capture the 

“side panel hook”

 while rotating.   

 
 
 
 
 
 
 
15.) 

To  fold  cart  sides  down  rotate  the 

“side 

panel  lock  levers”

  into  the  upright  position 

and fold panels down.   

 
 
 
16.) 

If desired, you may store cart on its end.  

Please exercise caution to prevent cart 
from falling over.  

 
 
 
 
 

 
 
 
 
 
 
 
 

 
 
 

IMPORTANT SAFETY INSTRUCTIONS 

 
 

A.  MAX LOAD: 600LBS.   NEVER OVERLOAD THIS CART 
B.  DO NOT

 Inflate tires more than 40 PSI 

C.  DO NOT

 Operate if any part is damaged or broken 

D. 

Lower fence rails when loading large items onto cart. 

E. 

Distribute load evenly in cart bed 

F.  DO NOT

 use on steep inclines where tipping may occur 

G.  DO NOT

 allow children to use this cart.  

IT IS NOT A TOY!

 

H. 

It is recommended that you 

DO NOT

 modify or use this cart for any application other than that for 

which it was designed.  
 

MAINTENANCE 

 

A. 

When not in use, store the cart in a place which is dry and out of direct sunlight.  

B. 

Periodically  check  tire  pressure.    Tire 
pressure should be between 36-40 PSI 

C. 

Periodically check hardware. 

D. 

Tighten any loose hardware.   
 

Содержание QH-UC






Отзывы: