manualshive.com logo in svg

Sunny Giken S550-MFW1U, Руководство по эксплуатации, Страница: 54 / 54

Поделиться
Скачать
Sunny Giken S550-MFW1U Скачать руководство пользователя страница 54

 

 

 

Overseas Specifications 

•

 Obtaining the CE Mark: (EMI: EN55011 Group1 Class A, EMS: EN61000-6-2) 

 

 

•

 FCC Compliance: 

    This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions; 

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

 

 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

Multifunctional Flash Microcomputer Programmer (S550-MFW1U)   

Operation Manual 

 

 

Date of Issue 

:  Apr, 2003 (The First Edition) 

 

Jul, 2011 (Rev.J) 

 

Editor 

:  SUNNY GIKEN INC. 

 

Published by 

:  SUNNY GIKEN INC. 

   

 

  3-1-9 Nishidai, Itami, Hyogo 

  

 

  JAPAN  664-0858 

 E-mail 

: 

[email protected] 

 

 

©2003-2011 Sunny Giken, Inc. All rights reserved. 

 

Multifunctional Flash Microcomputer [S550-MFW1U]   

53

 

Operation Manual 

Содержание S550-MFW1U























































Отзывы:

Нет отзывов