background image

Owner’s Manual — Sunlawn MM-1 

 

The roller apron keeps clippings from falling down between the cutting 
bar and the roller thus missing the grass catcher. The roller apron is 
installed just behind the cutting bar using the two screws provided. 
Once the roller apron is installed it is not necessary to remove it 
whether or not you are using the grass catcher. 

 

 

 
 

 

 
 
 
 
THE 1/3 RULE 
 

This is the key to enjoyable mowing and a healthy lawn.  
  
1.

 

The lawn should be mowed regularly, at least once a week during 
the growing season.  

2.

 

Be guided by observing the lawn and taking care not to remove 
more than 1/3 of the total height of the turf at any mowing.  

3.

 

Following this rule will stimulate the turf’s root growth, maintain its 
health, and encourage its natural ability to crowd out unwanted 
weeds. 

If the lawn has become too high (over 4 inches in height) then it is 
best to set the mower higher than usual and mow, then reset down to 
the normal level and mow again within a day or two.  
 
Removing too much of the turf’s height, especially in the heat of 
summer, can cause root shock and weaken the lawn; bringing down 
the height by successive mowings over two or more days can avoid 
this damage and maintain the health of the turf.  
 
If the lawn is overgrown (to higher than 4-5 inches) it may be 
advisable to use a brush cutter to remove the excess turf mass before 
resuming mowing at normal heights.  

 

MOWING: GENERAL INFORMATION 

Содержание MM-1











Отзывы: