background image

OPERATIONS 

Change of rotate speed of engine 

Engine oil number: SAE10W-40 or SAE15W-40 is recommended, and 
SAE10W-30 should be used if the temperature is below 

5°C

. If that 

kind engine oil is not easy to be found, please choose the substitute 
follow the parameter as below shows: 
 

The rotate speed of the engine should be changed frequently, and not to 
remain at one speed. This is good to the run in period of new one: to get 
average pressure for the components and cool them when pressure 
reducing. By varying the speed frequently, put some applicable burthen 
to each component and make them combined with each other. But don't 
put too much burthen. 

 
 

Avoid low rotate speed 

 
 

The components will only be smooth because of whetting during low 
rotate speed of engine. One should change different speed up the engine 
within the maximum rotate speed. But within the first 1500Km for a 
new scooter, don't rotate the throttle to maximum position, and don’t 
rotate the throttle suddenly. 

 
 
 
 

Cycle the engine oil before driving 

 

Gear oil 

After started the engine in hot or cool situation, don't drive immediately, 
let the engine has enough time for idle speed and let the engine oil 
reach to each important part of the component inside the engine.   

Please use SAE80W90 gear oil. 
 

Run in period of new scooter 

First maintenance 

A perfect run in period of a new scooter is very important to extend the 
life of the scooter and exert perfect performance. The following is the 
correct method during running in period of new one: 

The maintenance within the first 1000Km is the most important job for 
a scooter. After run in period of new one, all the engine parts and other 
parts are combined well with each other. Then one should adjust well 
the components, fasten the screw and change the used engine oil. Well 
execution of the maintenance within the first 1000Km guarantees a 
longer life and a better performance of the scooter. 

Maximum rotate speed 

Maximum rotate speed of the engine during the run in period of new 
one should be as following: 

 

9

Run in distance (Km) 

0-150 

151-300

301-800

801-1500

 

Speed of scooter 

(Km/h) 

30 40  50  60 

The maximum speed should not be over 80km/h in the first 3000Km. 

 
 
 

Note: 

The maintenance within the first 1000Km should be 

executed accordingly to the checking and maintaining chapter, 
and one should pay special attention to the words: "

Warning

" & 

"

Note

".

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL   SUNL

Содержание SL150-18
























Отзывы: