background image

SAFETY WARNINGS 

 

1. Keep all children and pets away from assembly area. Children and pets should be supervised 

while gazebo is being assembled. 

2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction such as fence, 

garage, and house, overhanging branches, laundry lines or electrical wires. 

3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe 

assembly. 

4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly. 

5. When assembling and using this product, basic safety precautions should always be followed to 

reduce the risk of personal injury and damage to equipment. Please read all instructions before 

assembly and use. 

6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the gazebo in the 

ground. If you wish to secure the pavilion to a wood deck or concrete surface, 16 anchors are 

provided for these surfaces.   

7. Check all bolts for tightness before and during usage. 

8. Please check your state and local regulations prior to installing this gazebo. Some jurisdictions 

may require permits for installation and use. Some special procedures may be valid in your area. 

9. While this gazebo is manufactured to withstand strong force winds through only the supplied 

ground stakes, in areas subject to frequent severe weather, securing the gazebo to a deck, concrete 

patio or footings should be considered. 

 

NOTE

: The gazebo’s roof and structure are not guaranteed against extreme weather conditions 

(storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned off 

regularly. Any damage caused by snow accumulation is not covered by the warranty. 

 
 
Care & Maintenance: 

 

Our steel components for garden accessories and furniture are treated with rust inhibiting paint that 

protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur 

once these protective coatings are scratched. This is not a defect and thus not covered by the 

warranty.   

 

To minimize this condition, we recommend care when assembling & handling the product to prevent 

scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up 

with rust inhibiting paint.   

 

Surface rust can also be easily removed with a very light application of common cooking oil. If 

surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start 

dripping on to deck or patio and caused damaging stains, which may be difficult to remove. This can 

be prevented if the above-mentioned measures are taken to keep the product from oxidizing. 

 

Made in China 

Содержание L-GZ605PST-A1














Отзывы: