background image

Step3 

15. 

Cover roof with big canopy (Q), do not fully extend. (Fig.15) 

16. 

Cover top with small canopy (P). (Fig.16) 

17. 

Hang  mosquito  netting  (R)  onto  long  round  pole  (H)  and  short  round  pole  (I),  using  mosquito  netting 

hooks (HH)). (Fig.17) 

18. 

Hang  wall  (S)  onto  top  long  beam  (E)  and  top  short  beam  (F),  using  mosquito  netting  hooks  (HH). 

(Fig.18). Then finish stretching big canopy (Q). 

19. 

Anchor column base (N) to ground using stake (GG), and then cover the column base with base cover. 

(Fig.19). Repeat for all columns. Go over all the assembly steps. 

 

 

Now the gazebo is ready for use. 

 

MAINTENANCE: 

1. This sun shelter is not a permanent structure and should be disassembled & stored away after use.   

2. Do not repack your sun shelter until it is completely dry.   

3. This sun shelter must be assembled by two adults or more.   

4. This sun shelter must not be left erect in windy conditions.     

 

WARNINGS:     

1. Assembly Instructions must be followed.     

2. Pegs supplied must be used to hold this gazebo in place when upright.   

  3. Warranty does not cover damage due to extreme weather conditions.     

4. Do not use candles, matches or open flames of any kind in or near a tent.   

5. Do not cook inside the tent.   

6.  Build  campfires  downwind  and  several  meters  away  from  a  tent  and  be  sure  to  fully  extinguish  campfires 

before leaving a campsite or before retiring for the night.     

7. Exercise extreme caution when using fuel-powered lanterns or heaters inside a tent and use battery-operated 

lanterns whenever possible.   

8. Do not refuel lamps, heaters or stoves inside a tent.   

9. Extinguish or turn off all lanterns before going to sleep.   

10. Do not smoke in a tent.   

11. Do not store flammable liquids inside a tent.   

12.  KEEP  ALL  FLAME  AND  HEAT  SOURCES  AWAY  FROM  THIS  TENT  FABRIC.  This  tent  is  made  of 

flame-resistant fabric. It is not fireproof. The fabric will burn if left in continuous contact with a flame source. 

 

Limited Warranty:

   

This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship 

of your item provided the item is maintained with care and used only for personal, residential purposes. The item 

is warranted to be free from defects in material or workmanship for a period of 

one (1) year

. We don't reimburse 

for  transportation  or  delivery costs, or  compensate  the  individual  or  any  outside  party  for  assembling  or 

disassembling the product. 

 

 

 

Содержание L-GZ224PAL-1








Отзывы: