User's Manual
8
MAIN MENU
TRIMS
MODES
TONE
INPUTS
SETTINGS
RECVR CABLE
GUIDE
MENU
MODE
MODE
EXIT
INFO
SYSTEM
+10
POWER
3
1
6
4
9
7
ENT
DIS
M3
M1
2
5
8
0
M2
PAGE
FAV
MAIN
OFF
VOL
CH
MUTE
PREV
CH
CD
AUDIO
MAIN
TAPE
AUX
ZONE2
DVD
VCR
SAT
TV
MENU
Previous
MODE
RECVR
Next
MODE
MAIN
EXIT
CHAPTER 1
Quick Start Guide
13. The TGR-3 now needs to be
setup correctly to suit your speak-
ers and system. The following On
Screen Display (OSD) menus are
used to enter and make three main
adjustments:
• Speaker Size
• Speaker Calibration
• Speaker Position
This setup needs to be done when
you use your system for the
fi
rst
time, or if you change anything
such as the ampli
fi
ers or speak-
ers, or the speaker position. The
calibration is also a good way to
check that your system is working
correctly. These adjustments are
made using the OSD as follows:
13.1 Press MENU on the remote to
bring up the MAIN Menu of the
OSD on your TV.
13.2 Use the joystick
pad left, right, up
and down buttons to
navigate through the
menus in the next
steps.
NOTE: you can quit the OSD at
any time by pressing EXIT on the
remote. Any changes you make
will be saved. There is no need to
navigate back through previous
pages, unless you want to make
more changes.
When the OSD is active, the TGR-
3 front panel display shows an
abbreviated message of where you
currently are in the menus.
8. Press the remote MAIN button
a few times to make sure you
are on the Main Menu in the
remote's display.
9. Set the remote to operate the
TGR-3 by pressing this
button.
We hope that the following details
will help you get started using your
TGR-3.
1. Take care to read and follow the
safety instructions on pages 2-3.
Also make sure that you read the
notes and details throughout the
manual, especially notes marked
with a warning triangle (
).
2. Add batteries to the remote control.
3. Connect your source equipment
and speakers to the TGR-3. See
the hookups on pages 15-24.
Make sure that all of your equip-
ment remains unplugged from
the AC mains until you have
made all the connections.
4. In your DVD player's Audio setup
menu, set the digital output to
BITSTREAM
. If this is not set cor-
rectly, the TGR-3 cannot decode
the digital information for 5.1 sur-
round sound playback.
5. The TGR-3 has a bass manage-
ment system which allows the bass
from each speaker to be redirected
to a subwoofer. Larger speakers
can play the full frequency range,
and smaller speakers such as
satellite types can have their bass
redirected. See page 42 for details.
Make a note of which speak-
ers you would like to play the full
frequency range (Large) and those
which will have the bass redirected
(Small). Also make a note of the
approximate distance of each
speaker from your listening posi-
tion.
6. The surround back speaker
outputs can be used for powering
surround back, side-axis, or Zone
2 speakers. See page 41
7. Turn on the TGR-3, and then turn
on your TV and source equipment.
10. Turn down the TGR-3 volume and
use the remote or front panel input
selector to select a video source.
11. Play a source, such as a DVD,
and bring up the volume to suit
your taste. Make sure the video
can be seen in the TV monitor.
12. Stop or pause the source.
