Sunfire MK IV Скачать руководство пользователя страница 16

Страница: 16 / 20

User's Manual

Specifications

Amplifier Output

2,700 watts rms (3.3

Ω

impedance)

High Cut Filter

35 Hz - 100 Hz Adjustable.

Frequency Response

18 Hz - 100 Hz

Power Line Voltage

US model

120 VAC 50/60 Hz

International model

230 VAC 50/60 Hz

Dimensions

11" x 11" x 11"

Weight

48 lbs

Finish

Black anodize and black lacquer.

Line power consumption:

600 W average, 18 Hz to 80 Hz, at
absolute maximum continuous output.

8 watts at idle.

2700 W peak, time limited basis.

Output levels:

Greater than 110 dB peak SPL
(includes room gain) from 18 Hz to
80 Hz.

A typical Sunfire subwoofer can be
expected to ‘best’ its specified minimum
peak SPL by several decibels.

Total Harmonic Distortion

Typically less than 1/10 of the funda-
mental between 18 to 80 Hz.

Measurement method is near field, dual
microphone technique. Distortion
decreases with decreasing level.

Input sensitivity for full output:

250mVrms from left input with volume
control at 0dB, 60mVrms with volume

control fully clockwise

0.75Vrms from right input with volume
control at 0dB, 200mVrms with volume

control fully clockwise

Input impedance:

12 k

Ω

for Line-Level inputs

15 k

Ω

for Hi-Level inputs

Driver:

Extra large magnet and long throw
mechanical design yield very high back-
emf. The result is extraordinarily high
operating efficiency – that is, more
acoustic output for each watt of input.

Internal system gain:

50dB from left input jack to speaker with
the Bass Level control at 0dB, 62dB with

the control fully clockwise

40dB from right input jack to speaker
with the Bass Level control at 0dB, 52dB

with the control fully clockwise

The Sunfire Subwoofer utilizes
differential gain on the left and right
inputs to retain both L+R and L-R
information.

Manual part number 913-016-00 Rev D

Содержание MK IV





















Результаты поиска

Содержание MK IV

Отзывы:

Похожие инструкции для MK IV

Бренды по названию

Популярные бренды

Sunfire MK IV, Руководство пользователя

Результаты поиска

Содержание MK IV

Отзывы:

Похожие инструкции для MK IV

Бренды по названию

Популярные бренды