Sunex HD 5712 Скачать руководство пользователя страница 3

Страница: 3 / 10

5712 - 12 Ton Power Unit
5720 - 20 Ton Power Unit

5720AH - 20 Ton Pneumatic Power Unit

5712 - (2) 3/4" x 10" Pins
5720 - (2) 1" x 12" Pins
5720AH - (2) 1" x 12" Pins

5712 - (2) 1" x 2" x 10" Plates
5720 - (2) 3/4" x 3" x 12" Plates
5720AH - (2) 3/4" x 3" x 12" Plates

Examine box contents, then proceed with the following instructions.

ESTIMATED ASSEMBLY TIME: 30 MINUTES

TOOLS NEEDED

1/2" and 5/16" Box Wrenches

ACCESSORIES

PARTS LIST

Press Frame - 1

Press Bed - 1

Press Feet - 2

Z Bar - 1

1/2"-13 x 1-1/2" Hex Head Bolts - 4

1/2" Nuts - 4

Washers - 4

5/16"-13 x 1" Hex Head Bolt - 1

Press Pins - 2

Power Unit - 1 (5712 & 5720 ONLY)

Pneumatic Power Unit - 1 (5720AH ONLY)

Pump Handle & Extension - 1

2" Punch - 1

Accessory only -

Not needed for assembly

Bearing Shield - 1

Accessory only -

Not needed for assembly

Press Plates - 2

Accessory only -

Not needed for assembly

5712, 5720, 5720AH

rev. 10/03/18

5712

- 12 Ton Hydraulic Shop Press

5720

- 20 Ton Hydraulic Shop Press

5720AH

- 20 Ton Air/Hydraulic Shop Press

Содержание 5712











Результаты поиска

Содержание 5712

Отзывы:

Похожие инструкции для 5712

Бренды по названию

Популярные бренды

Sunex HD 5712, Руководство пользователя

Результаты поиска

Содержание 5712

Отзывы:

Похожие инструкции для 5712

Бренды по названию

Популярные бренды