background image

4912DAH and 4920DAH 

rev. 02/28/12

WARNINg INFORMATION

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

             

 

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING 
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsiblity of the 
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or 
not legible, contact Sunex for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to 
and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator 
comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of bottle jacks is subject to certain hazards that cannot be prevented by mechanical means, but only by the exercise of 
intelligence, care, and common sense. It is essential to have personnel involved in the use and operation of the jack who are careful, 
competent, trained, and qualified in the safe operation of the jack and its proper use when servicing motor vehicles and their components. 
Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading, off-centered 
loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not intended.

METHODS TO AVOID HAZARDOUS SITUATIONS

• 

Read, study, understand and follow all instructions before operating this device.

• 

Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or unstable 
due to loose or missing hardware or parts. Make corrections before using.

• 

Lift only on areas of the vehicle as specified by the vehicle manufacturer.

• 

Wear eye protection that meets ANSI Z87.1 and OSHA standards.

• 

Do not use jack beyond its rated capacity.

• 

This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before 
working on the vehicle.

• 

Use only on a hard level surface.

• 

Center load on saddle. Be sure setup is stable before working on vehicle.

• 

Do not use any adapters unless approved or supplied by Sunex.

• 

Always lower the jack slowly and carefully.

• 

This product contains one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive 
harm. 

Wash hands thoroughly after handling.

• 

Failure to heed these warnings may result in serious or fatal personal injury, property damage or both.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, 
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS 
could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

Содержание 4912DAH














Отзывы: