Sunell Security SN-TPT4231 Скачать руководство пользователя страница 34

Страница: 34 / 87

Quick Configuration

Dual Vision Light Load Thermal PTZ

User Manual

Issue V1.0 (2019-04-03)

4.1.7.3 Schedule Linkage

Operation Procedure

Step 1

Choose

Configuration

Thermal

Schedule Linkage

The

Schedule Linkage

page is displayed, as shown in Figure 4-11.

Figure 4-11

Schedule Linkage

Step 2

Tick the output channel.

Step 3

Enable “Alarm Record”, “SMTP”,”FTP” button.

Step 4

Set schedule linkage.

Method 1

：

Click

left mouse button to select any time point within 0:00-24:00 from

Monday to Sunday as shown in Figure 4-11.

Method 2

：

Hold down the left mouse button, drag and release mouse to select the

alarm time within 0:00-24:00 from Sunday to Saturday.

NOTE

When you select time by dragging the cursor, the cursor cannot be moved out of the
time area. Otherwise, no time can be selected.

Method 3

：

Click

in the alarm time page to select the whole day or whole week.

Deleting alarm time:

Click

again or inverse selection to delete the selected alarm

time.

Step 5

Click

Apply

Содержание SN-TPT4231
























































































Результаты поиска

Содержание SN-TPT4231

Отзывы:

Похожие инструкции для SN-TPT4231

Бренды по названию

Популярные бренды

Sunell Security SN-TPT4231, Руководство пользователя

Результаты поиска

Содержание SN-TPT4231

Отзывы:

Похожие инструкции для SN-TPT4231

Бренды по названию

Популярные бренды