SunEarth SolaRay 2 Скачать руководство пользователя

Страница: 37 / 50

P.33

Circulator Pump

The circulator pump shall be a wet rotor small circulator with a cast iron, stainless steel,

brass or polymer body and a metal or polymer impeller. The pump motor shall be

induction or permanent magnet ECM driven. The pump shall be rated for: maximum fluid

temperatures of no less than 180

F and pressures of no less than 125 PSI. The maximum

rated amperage shall be no more than 1.5 Amps and the maximum rated power draw shall

be no more than 135 Watts.

Expansion Tank

The expansion tanks shall be rated for non-potable propylene glycol based heat transfer

fluids. The maximum working temperature shall be no less than 180

F and the maximum

working pressure shall be no less than 75 psi. The expansion tank volume shall be not less

than 2.0 gallons and the acceptance volume shall be not less than 1.0 gallon.

Heat Transfer Fluid

The heat transfer fluid shall be buffered propylene glycol based and shall have a maximum

operating temperature of no less than 280

F. If the HTF has a measurable flash point, at

the concentrations used in the system, the HTF shall have a flash point of 400

F or higher.

Thermostatic Mixing Valve

The thermostatic mixing valve shall have a bronze, brass or stainless steel body with a

rated maximum working temperature no less than 200

F and a rated maximum working

pressure no less than 125psi. The range of temperature set points shall be at least 18ºF

(10ºC) and shall include a set point of 120ºF (50ºC). The Thermostatic Mixing valve shall

be third party listed and certified to one of the following ASSE standards: ASSE 1016;

ASSE 1017; ASSE 1070.

Ball Valves

Ball valves shall be of bronze, brass or stainless steel construction. Maximum working

temperature shall be no less than 200

F and maximum working pressure shall be no less

than 125 psi.

Three-Way Valves (Optional)

Three-Way valves shall be of bronze, brass or stainless steel construction. Maximum

working temperature shall be no less than 200

F and maximum working pressure shall be

no less than 125 psi.

Boiler Drains

(A.K.A. Charge Valves; Fill Valves; Drain Valves; Purge Valves)

Boiler Drains shall be of bronze, brass or stainless steel construction. Maximum working

temperature shall be no less than 200

F and maximum working pressure shall be no less

than 125 psi.

Pressure Relief Valve

The pressure relief valve shall be of bronze, brass or stainless steel construction with a

pressure setting between 30psi and 150psi. The pressure relief valve shall be set to

discharge at a pressure below the maximum design pressure of all other components in the

collector loop.

Check Valve

(A.K.A. Non-Return Valve)

The check valve may be a stand alone component or may be integral to the circulator

pump. The check valve shall be spring type of bronze, brass or stainless steel or polymer

construction. Maximum working temperature shall be no less than 200

F and maximum

working pressure shall be no less than 125 psi.

Air Vent

The air vents shall be of bronze, brass or stainless steel construction. Maximum working

temperature shall be no less than 200

F and maximum working pressure shall be no less

than 125 psi.

Appendix A

Содержание SolaRay 2



















































Результаты поиска

Содержание SolaRay 2

Отзывы:

Похожие инструкции для SolaRay 2

Бренды по названию

Популярные бренды

SunEarth SolaRay 2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SolaRay 2

Отзывы:

Похожие инструкции для SolaRay 2

Бренды по названию

Популярные бренды