Sun Microsystems Ultra Enterprise 3000 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 48

Sun Microsystems Ultra Enterprise 3000 Скачать руководство пользователя страница 40

3-6

Ultra Enterprise 3000 System Installation Guide—May 1996

3

Note –

This screen display is an example only. The actual message displayed

on the screen will depend on the software running on your system.

If firmware indicates a hardware problem at this time, refer to the
Ultra Enterprise3000 System Manual, Part 3, “Troubleshooting,” for further
instructions.

Boot the system using the procedure that is appropriate for your operating
system. See the Preface, “UNIX Commands” for a reference to documentation
that describes this procedure.

3.2.2 Interpreting Status LED Patterns

If there is no terminal on the system, basic system status information is
available on the front panel LEDs, as shown in Figure 3-4.

4-slot Ultra Enterprise 3000, Keyboard Present

OpenBoot -.- FCS, --- MB memory installed, Serial #---.

Ethernet address -:-:--:-:--:--, Host ID: ------.

«
...
38
39
40
41
42
...
»

Содержание Ultra Enterprise 3000

















































Отзывы:

Нет отзывов