Sun Microsystems Ultra Enterprise 3000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

Sun Microsystems Ultra Enterprise 3000 Скачать руководство пользователя страница 35

3-1

Powering the System On and Off

3

This chapter contains information about powering the system on and off,
reading boot messages, and interpreting system status by viewing the LEDs.

3.1 Using JumpStart Automatic Installation

The Enterprise 3000 system can use the JumpStart™ automatic installation
feature that is described in installation documents for Solaris software. The
software that enables this feature is present on a hard disk in your system if the
system was built at the factory with internal disk boards or disk trays.

JumpStart will run only when the system is powered on for the first time.

Caution –

JumpStart may incorrectly install the system as a standalone

workstation. You should prevent JumpStart automatic installation from
proceeding if the appropriate server-specific configuration information is not
in place. Information about the JumpStart feature is on a card titled “JumpStart
Installation Instructions” that is provided with the system documentation.

To prevent JumpStart installation from occurring unintentionally:

•

Do not connect the system to a network when you power it on initially.

•

Do not place a Solaris release CD-ROM in a drive when you first power on
the machine.

!

«
...
33
34
35
36
37
...
»

Содержание Ultra Enterprise 3000

















































Отзывы:

Нет отзывов