Sun Microsystems StorEdge D2 Скачать руководство пользователя страница 27

Страница: 27 / 118

Chapter 1

Sun StorEdge D2 Array Overview

1-11

1.7.1

ESM

The Ultra3 SCSI Environmental Services Module (ESM) is shown in the following
figure.

FIGURE 1-5

ESM Front (Viewed from the Back of the Array)

TABLE 1-5

describes the connectors, switches, and LEDs on the ESM.

TABLE 1-5

Connectors, Switches, and LEDs on the ESM

SCSI-

connector

The two host connectors on each ESM enable the array to connect to two separate
hosts. External terminators are not required. Termination power is sensed through the
SCSI

Termination Power LED.

SCSI-

Termination

Power LED

Green: Termination power is being supplied from the host to the associated connector.

Configuration
Options switch bank

Four-position, piano-style switches to set options described under “Configuration
Options Switch Bank” on page 1-14.

SCSI-A

SCSI-B

4 3 2 1

Configuration

Options

Unit ID

SCSI

SCSI-B connector

SCSI-A connector

SCSI-A Termination Power LED

Configuration Options switch bank

Power On/SCSI Active LED

SCSI-B Termination Power LED

ESM Over Temperature/Code Download LED

Unit ID

Содержание StorEdge D2























































































































Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды

Sun Microsystems StorEdge D2, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание StorEdge D2

Отзывы:

Похожие инструкции для StorEdge D2

Бренды по названию

Популярные бренды