manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000E, Руководство по установке

Поделиться
Скачать
Sun Microsystems SPARCcenter 2000E Скачать руководство пользователя страница 15

Before You Start

1-3

1

CAUTION

Risk of equipment damage. To reduce
the risk, follow the instructions.

AC

A terminal to which alternating
current or voltage may be applied.

ON

The principal and stand-by switches
are in the ON position.

OFF

The principal switch is in the OFF
position.

STAND-BY

The stand-by switch is in the
STAND-BY position.

PROTECTIVE EARTH

Protective earth conductor.

CHASSIS

Frame or chassis terminal.

FUSE REPLACEMENT

For continued protection against risk

MARKING

of fire and electric shock, replace
ONLY with same type and rating of
fuse.

Caution – DO NOT make mechanical or electrical modifications to the cabinet.
Sun Microsystems is not responsible for regulatory compliance of modified
cabinets.

Caution – Power off the cabinet and all equipment connected to it before
performing any of the procedures described in this book.
The system chassis power must be turned off, and the AC power cord must
remain plugged in to ensure a proper ground.

!

!

!

!

Содержание SPARCcenter 2000E























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды