background image

Assembly Procedures

(ELECTRICAL CONNECTOR

INDICATES BACK OF BENCH)

Lay the bench upside down on the
floor. Locate the two stand legs.

1

Remove the six 5/16” x 1” bolts and
5/16” washers installed in the bench.
Attach the stand legs with the skirt
mounting holes toward the back of the
bench as shown. Install center bolt first.
You may have to gently push the sides of
the legs in to align holes. Tighten with
the Allen wrench.

2

SKIRT MOUNTING HOLES

Unpacking and Inspection

Your sunbed comes in two cardboard cartons. Pull back the plastic
sheet and, with a helper, grasp the bench and pull it from the carton
bottom, leaving the plastic wrap and the carton packaging. Do not try
to lift the unit with the plastic still on as it may slip. Do the same with
the canopy.

The canopy box contains the canopy and a pair of gas springs. The
bench box contains the bench, assembly hardware and stand legs.

Inspect the items and make sure they are free from any visible damage.
Report the extent of any damage to the transportation company.

In addition to the hex wrench supplied in the hardware kit, you will
need a 

#2 Phillips screwdriver

.

Allen-head Bolt 5/16” x 1”

Quantity 2

5/16” Metal Washer

Quantity 2

Bushing

Quantity 2

Allen-head Bolt 5/16” x 1 1/2”

Quantity 2

Nylon Washer

Quantity 2

Hinge Brackets

(1) left, (1) right

Hex (Allen) Wrench

Quantity 1

Safety Goggles

Quantity 1

Hardware Inventory   

(These items and a small pillow)

Page 2  -  26713-01A

Position the side skirts at either end of
the base. Install two #8 x 1/2” screws
through the pre-drilled holes of the side
skirt into the back of the leg support.
Repeat for the other side skirt.

3

Install screws here

SHORT BOLT

Turn bench over. Install hinge brackets to ends of
bench such that the short boss engages the stud
above the bolt hole, and the long boss engages the
hole below the bolt hole. Secure using 5/16” x 1”
Allen-head bolts and 5/16” metal washers. Tighten
bolt snug, then an additional half turn.

5

STUD

Turn the bed around and put the
front skirt in place, making sure the
ends wrap over the side skirts.
Velcro® pads at each end secure the
front skirt.

4

Содержание 24 X-Power









Отзывы: