background image

10 

 

Adjusting the Tilt 

If your beer cooler seems unsteady or you would like the door to close more easily, you can use the 
leveling legs to adjust the tilt of the unit.  

Be sure that the unit is in its final position when making adjustments to the tilt and that it is plugged into 
a grounded 3-prong outlet.  

WARNING: 

           Two or more people are required to move and/or install the refrigerator. Failure  

    to do so may cause back or other injury.  

  

  

 

 

 

 

 

  Turning a leveling leg to the right will lower the appliance toward the position of the leg. Likewise, 

turning to the left will raise the unit away from the leg.  

  Several turns of the leveling legs may be required before the tilt of the appliance is properly 

adjusted.  

  Turning both front legs the same amount to the left will tilt the kegerator to the rear. This adjustment 

makes it easier for the door to close. 

NOTE:

 

It is easier to adjust the leveling legs if someone else pushes against the top of the 

appliance to take the weight off the legs.  

 

Draft Arm Assembly 

1.  Slide the gasket over the wing nut on the bottom of draft arm assembly beer tubes.  Slide gasket up 

beer tubes to draft arm base. 

2.  Push the wing nut on the beer tube of the draft arm assembly through the hole in the top of the 

cabinet until the draft arm is resting on cabinet top. 

3.  Align holes in draft arm base with holes in gasket and pilot holes in cabinet, then secure the guard rail 

to the cabinet top. 

Beer Kegs and Keg Tappers 

Your kegerator cooler comes 

with a double tap and will accommodate two “Sixth Barrel” kegs, also 

known as “sixtels” or “logs”. Each sixtel has a height of 23-3/8” and a diameter of 9-1/4”, and hold 5.16 
gallons of beer. Two Cornelius (“Corny”) kegs will also fit. The unit will not hold a half barrel or quarter 
barrel, although it can take one “Slim Quarter” barrel. 

The Sankey type keg tappers supplied with the kegerator are the most widely used in the United States.  
However, other types of keg tappers can be used.  Before installing a keg tapper, check with your beer 
distributor to make sure that the Sankey type keg tapper can be used. 

If you need keg tappers other than the Sankey type, it is recommended that you purchase the tappers 
you need from your beer distributor.  Please keep the Sankey type keg tappers for future use.  The 
Sankey system is becoming more popular.  It may be purchased from our Sales Department at 

718-893-

3900

 

Leveling leg 

Содержание SBC56ADA





















Отзывы: