Summit to Sea SHALLOW DIVE Скачать руководство пользователя страница 83

Страница: 83 / 91

IMPORTANT TO READ

WARNING

: In the unlikely event that there is a rapid decompression, the individual inside

the chamber must EXHALE. Please make sure that each individual receiving treatment
understands this precaution.

WARNING

: Do not replace the compressor with any other model. The chamber is designed

to work specifically with the compressor provided. For added safety, the compressor will not
exceed the test pressure for the chamber.

WARNING

: Do not tamper with the pressure regulation valves. These are factory set and

there are no user adjustments. Any sign of tampering with these valves will void the
warranty.

WARNING

: Do not use the chamber in a manner where the chamber could roll off the

surface causing a fall. Always use on a surface large enough to prevent rolling off and
causing a fall.

WARNING

: Never take a treatment alone. Always have someone outside the chamber to

assist you.

WARNING

: Do not use the electric compressor in the rain or around running water as this

could cause electric shock.

WARNING

: Wear comfortable clothing and lay on a mat, towel or blanket while in the

chamber to limit contact with the chamber surface and to improve comfort and safety.

Содержание SHALLOW DIVE




























































































Результаты поиска

Содержание SHALLOW DIVE

Отзывы:

Похожие инструкции для SHALLOW DIVE

Бренды по названию

Популярные бренды

Summit to Sea SHALLOW DIVE, Инструкция по эксплуатации

Результаты поиска

Содержание SHALLOW DIVE

Отзывы:

Похожие инструкции для SHALLOW DIVE

Бренды по названию

Популярные бренды